Inspection and Replacement of Active Motor Mounts

Inspection and Replacement of Active Motor Mounts

The problems with active mounts usually stem from the vacuum or electronic side, not the mount itself. 

Motor mounts aren’t glamorous or impressive or a high-performance item, but they’re a critical part of any vehicle’s drivetrain and its entire noise/vibration/harshness package. Motor mounts (and transmission mounts) help keep several hundred pounds of engine and drivetrain aligned at a precise angle, attaching the engine and transmission to the chassis or subframe. These rubberized mounts help isolate the vibrations from the engine and dampen the tendency for the engine to twist to one side due to torque on acceleration. They’re part of a system that keeps the drivetrain situated properly and ensures a quiet and smooth experience for the driver. 

For decades, motor mounts were just a sandwich of vulcanized rubber inside inner and outer metal sleeves; while this is a simple and dependable design, rubberized motor mounts tend to dry out and shrink after time and many heat/cool cycles, meaning they’ll transmit more vibration or may fail completely and need to be replaced. Some European models use a hydraulic mount, a gel-filled donut with sealed chambers and passages. This more advanced design is tuned to respond to certain vibration frequencies and amplitudes that go along with RPM and load. 

Active motor mounts, on the other hand, are designed with electronic or vacuum controls that can alter stiffness on demand and are featured on a number of performance brands. In design and function, they’re not too dissimilar from the solenoids and controls for active suspensions, including the magnetorheological fluid used in active shock absorbers. 

On some Jaguar models, the active mounts are part of the driving mode package and can be adjusted to provide more feedback for the driver in Sport mode. They’re designed to be dynamic and can even change stiffness slightly during gear changes or while cornering. The problems with active mounts usually stem from the vacuum or electronic side, not the mount itself. 

Active Motor Mounts Design

Earlier designs of active motor mounts relied on engine vacuum to regulate their damping behavior. An engine pulls more vacuum at idle, and the mounts would be softer and more compliant to easily soak up NVH. Acceleration and load means less vacuum, and mounts were designed to limit excessive engine movement as they firmed up. That, of course, means a vacuum line and port that could be prone to wear and failure. 

Later designs worked much the same way, but rely on an electronic actuator that’s controlled by the vehicle’s ECU, based on input from sensors and programming. This design is more precise and doesn’t have the lag time that goes along with vacuum actuation, adjusting the firmness of the mounts on the fly. Some active mounts can even generate a counter-vibration that’s tuned to neutralize the vibration frequencies from the engine’s rotating assembly, not unlike a balance shaft design. These mounts are common on models from Audi, BMW, Jaguar, Lexus, Toyota, Honda and other makes. Active motor mounts are commonplace on any vehicle that has a cylinder deactivation system, helping to soak up vibrations as the engine’s cylinders shut down. 

When Motor Mounts Fail

There are usually some pretty clear signs of failing motor mounts. These include:

  1. Excessive vibration that can be felt through the steering wheel or floorboards, during certain RPM or load ranges, while idling in gear or using the AC.
  2. Noticeable clunk or bang when putting the vehicle in gear, accelerating or decelerating (this can easily be mistaken for bad U-joints or CV joints).
  3. Noticeable torque steer on a FWD vehicle.
  4. The engine moves in its motor mount cradle when an assistant revs the engine, in gear and foot on the brake.

One failed mount puts extra stress on the other mounts and will usually lead to their failure as well. When the engine is wobbling and torquing around underhood, it stretches wiring and puts strain on vacuum lines, radiator hoses, belts, throttle and shift linkages. In extreme cases, a misaligned engine and transmission can change driveline geometry and wear out CV joints, or the engine can even come in contact with the radiator fan and shroud. 

It’s also worth noting here that oil or transmission fluid leaks can degrade the rubber of a motor mount, softening it and hastening its failure. In instances like this, the leak will need to be addressed as well. Also, an active misfire code like P0300 or P0304 can cause vibrations that are harsh enough to destroy engine mounts within weeks. 

The ECU might store codes as well, but these can be misleading: for instance, P0171 or P0400 codes indicate a failed EGR or clogged PCV that will produce an idle so rough that it can mimic a failed motor mount. Codes like P1586 can confirm a failed solenoid and internal electronics. 

Your best bet, though, is still a visual inspection: does the engine torque to one side when an assistant “power-brakes” it with the transmission in gear? Can you see a sooty appearance to the body of the engine mount? Does the rubber look dry-rotted, degraded or is it starting to separate from the metal body?

Repair and Replacement

Inspect other components like wiring harnesses, throttle linkage, transmission linkage, heat shields, hoses, vacuum lines, intake ducts, drive axles, etc., to ensure that they haven’t been damaged by excessive engine movement. When servicing, make sure the oil pan, transmission and other parts are properly supported to avoid damage and be aware that other components might need to be removed in order to access the motor mounts. 

Mounts should be replaced in pairs or sets, not one at a time; a single mushed-out motor mount can put undue stress on the other mounts. After installing the mounts, check and verify the clearance around exhaust and cooling components to make sure the engine’s position is correct. Active systems might require calibration or functional testing; be sure of the right process for your year/make/model. 

After installation, always road test the vehicle at different speeds to be sure the vibration problem’s been eliminated. Inspection of the motor mounts should go along with other routine maintenance, such as changing a timing belt, and motor and transmission mount inspection should be part of any collision repair work. 

Depending on the design of active engine mounts, a technician should look for DTCs, module commands, wiring (power and ground) and the mount’s response to any commands or switching of modes. Be mindful that the details of repair and replacement can vary a lot from one year/make/model to another. 

You May Also Like

Early European EVs: A New Opportunity for Shops

While these vehicles still represent a relatively small percentage of the vehicle population, they present an opportunity for shops.

The first wave of European battery-electric vehicles (EVs) has reached an important milestone. Many of the vehicles introduced before the 2020 model year have now aged beyond their original factory warranties and are finding their way into independent repair facilities. While these vehicles still represent a relatively small percentage of the vehicle population, they present an opportunity for shops willing to develop the skills, tooling and safety procedures required to service high-voltage systems.

Troubleshooting: BMW ZF 6HP26 Keeps Going Back into Park

A 2009 BMW equipped with a ZF 6HP26 has a complaint of going back into park when shifted into forward or reverse.

Mercedes-Benz M276 Biturbo: Operation, Failures and Diagnostics

Issues you might run into with this engine include wastegate rattle, linkage wear and underboost complaints, among others.

Audi, Volkswagen Turbo Diagnostics: Turbine Speed and Lag

The signs of a leaking turbocharger system start with a lack of power or random misfires on Audi and VW engines.

How to Retrofit a Truck’s AC System from R-134a to R-456A

This is a straightforward retrofit procedure, but there are a few details that matter.

Other Posts
PennGrade Offers Gear Oil Fill Pouches

The pouch is designed to help reach tight and awkward fill locations where bottles can be difficult to maneuver.

Toyota Transmission Lost Communication with TCM

A 2011 Toyota Camry equipped with a U660E transmission has come into the shop in default with a trouble code U0101 “Lost Communication With TCM” set.

Mini Cooper Clutch Replacement

Mike Greer’s advice: Don’t turn away an all-wheel Mini Cooper clutch replacement job just because it seems too complicated.

Why Are Cabin Air Filters Electrically Charged?

We have the answer in episode two of That’s Not a Stupid Question.