VW Intake Manifold

VW Intake Manifold

Some owners of VWs & Audis have experienced performance or drivability concerns tied to faulty intake manifolds.

TSI Intake Manifold Failures

Many owners of TSI-equipped VWs and Audis have experienced performance or drivability concerns which include poor idle, power loss, random cylinder misfires, and an illuminated check engine light with a P2015 code. These symptoms are most commonly tied to faulty intake manifolds, but what exactly is it that fails?

Construction

The intake manifold is composed of two polyamide shells which are plastic-welded together. Trough-shaped flaps, also known as tumble valves, can be found inside each intake port (Figure 1). A potentiometer is used to measure the flap position (Intake Manifold Runner Position Sensor G336). The flaps are closed when the engine is not running, and will open once certain running criteria have been met.

Thanks to their shape, as well as their arrangement in the intake port, the airflow is improved when the flaps are in the open position. When they are closed, they cause the air to tumble, or swirl, into the combustion chamber (Figure 2).

So, why would we want the air to tumble or swirl? We all know that a football will travel farther and straighter with a spiral; the same goes for air flowing through the manifold. Tumbling air offers a number of advantages, but only at certain engine speeds and load conditions. This is why the valves need to be able to open and close based on driving conditions and other criteria.

Tumble Valve Operation

Vacuum is applied to the actuator to cycle the tumble valves open or closed. Herein lies the weak point of the system – the plastic linkage. If the flaps were to become stuck due to carbon buildup, then the plastic linkage could easily bind up and snap. This linkage is not serviceable separately, so the entire manifold needs to be replaced. These issues were so common that later production units were revised with more robust linkage to resist breakage (Figure 2).

Tumble valves (Figure 3) were first used in FSI engines to actively switch between two modes of operation: Stratified charge operation and homogeneous operation. FSI and TSI engines use the tumble valves to switch from a stratified charge operation in the part-throttle range and a homogeneous air/fuel mixture in the full-throttle range. The ability to switch between these two modes helps to optimize the engine operation throughout the rev range while maximizing power and efficiency (Figure 4).

Tips & Tricks

Start with your normal diagnostic process. If you see a P2015 code in the ECM, or another code pertaining to the tumble valve/runner flaps, remove the air box to access to the side of the intake manifold. Remove the vacuum hose from the actuator and try to cycle the linkage by hand. If you can’t move the linkage by hand, it’s time to remove the intake manifold and look for carbon buildup inside (Figure 5).

 The manifold will also need to be replaced if you find that the linkage has broken off, or if the cam inside the manifold has snapped off (Figure 6).

You May Also Like

AUDI Outside Air Temperature Readings

Incorrect readings can be avoided.

With the recent changing of seasons, it is possible to see a 20- to 30-degree temperature change from when the car is parked in the evening and driven again in the morning. Some customers may say they think the ambient temperature is not reading accurately. To achieve a "smoothing" effect of the displayed outside ambient temperature, the value shown does not instantaneously follow the temperature sensor measurement.

Mercedes-Benz ABC Suspensions

The system provides great ride & handling, but it can be complicated to service if you do not have the right training.

Audi TFSI/FSI: Oil Consumption And Carbon Buildup

Technical Service Bulletins can be valuable in helping solve vehicle problems. But sometimes, it takes multiple TSBs to find a pattern failure or the “root cause” of a problem. In the case of the Audi/VW 2.0L Fuel Stratified Injection (FSI) engine introduced in 2006, three problems related to engine carbon and fuel issues are connected

BMW Headlight Service

Taking a guess can get very pricey if you can’t return the part. 

BMW Diagnostics: Low Airflow After Cabin Filter Replacement

Models:  F97 X3 M  F98 X4 M G01 X3 G02 X4 G20 3-Series SITUATION After replacing the microfilter during a previous service, the customer notices that the ventilation system airflow rate is noticeably less. This leads to perceived lower cooling power. The customer may also notice that external odors enter the vehicle. Related Articles –

Other Posts

Does Your Customer’s AUDI Oil Appear To Be Leaking?

Here are the service procedures required for when oil leaks from the transmission pan gasket or the transfer case.

Autel Energy Europe Releases MaxiCharger Launch Plan

Autel introduced the MaxiCharger Megawatt Charging System satellite launch plan at the Nordic EV Summit 2024.

Autel Releases the AC Elite G2 Charging Series 

The charger can be used in various settings, such as public commercial parking areas, residential areas, hospitals and service areas.

Autel’s ADAS Bay Max Vehicle Lift

Learn how this lift integrates mechanical repair, four-wheel alignment, and ADAS calibration, prioritizing efficiency and space utilization in your shop.