Why Does My Car Shake When I Brake?

Why Does My Car Shake When I Brake?

Assuming that new pads and rotors will automatically fix the problem will only create more issues.

Judder is a vibration that can be felt in the seat or steering wheel, but it will not cause pulsing of the brake pedal. Judder can occur in a vehicle with zero runout or disc thickness variation (DTV), and is caused by brake torque variation (BTV).

BTV occurs when there is a variation of torque across the face of the rotor that causes the rotor to slip and catch as brake pads pinch the rotor. BTV may be caused by an inconsistent rotor finish, metallurgy or uneven deposits of friction material on the face of the rotor.

Assuming that new pads and rotors will automatically fix the problem will only create more issues with the customer when the vehicle inevitably comes back.

Knowing the difference between pulsation or DTV and judder/BTV is critical to solving any brake complaint and avoiding a problem in the first place. Assuming that new pads and rotors will automatically fix the problem will only create more issues with the customer when the vehicle inevitably comes back.

Rotor Finish and Transfer Layers

The friction between the two surfaces changes forward motion and braking force into heat, but there is a lot of science that goes into what happens at the molecular level to make that happen.

Most semi-metallic brake pads use the two different surface materials of the pad and rotor to make friction. The abrasive action wears away the two surfaces, but ceramic and some NAO pads transfer a thin layer of pad material onto the surface of the rotor. The transfer layer is bonded to the rotor’s surface and cannot be washed away by water or wheel cleaners. The only way to remove it is by using a brake lathe or abnormal heat. With this type of pad, it is critical to machine the rotor with the correct surface finish and follow the recommended break-in procedure so the transfer layer can be established.

Adherent friction is easier on rotors, but the pads become the primary wear component. The layer is always being worn and replenished by the brake pad during braking, so these pads produce dust. The smoothness of the friction surface of a rotor is described in terms of microfinish or RA factor. RA stands for “roughness average” and represents a way to measure the smoothness of a rotor. Most lathes on the market will yield very acceptable RA factors when they are in good condition and are used properly. The finish is essential to transfer material for organic and ceramic friction materials. The correct finish is also essential for semi-metallic pads so they can have the correct coefficient of friction during initial break-in.

You May Also Like

Top 10 Brake Mistakes

Here are the top 10 brake mistakes technicians can make.

1. Not cleaning the brake slides and hardware: Just slapping new pads and abutment clips where the old ones once resided never works. The caliper bracket slides need to be clean and free from rust. Don’t get overly aggressive with the wire brush. Some automakers are using anti-corrosion coatings and surface treatment on the brake caliper bracket lands. If brake cleaner and a nylon brush can’t tackle the deposits, you might be making the corrosion worse by using a wire wheel or file.  

Fine-Tuning Your Wheel Balancing Process

The first step to a smooth ride and well-balanced tire has nothing to do with the balancer.

Drilled and Slotted Rotors

There’s real science behind the location of holes, slots and grooves in today’s brake rotors. Plus, they look great too.

Laying Out Your Shop for ADAS/EV Repairs

With so many vehicles equipped with some form of ADAS, rethinking your electronics layout or plan might be in order.

Air Ride Suspension Diagnostics

The key to understanding the embedded logic of air ride systems is using service information.

Other Posts

Servicing Mercedes-Benz AMG Brakes

Take a look at some of the things you need to know in order to service the brakes on a Mercedes-Benz AMG vehicle.

Identifying Brake Issues With Brake Dust

Brake dust can indicate what could be wrong. This video is sponsored by Auto Value and Bumper to Bumper.

Considerations for Counter Professionals When Recommending Brake Pads to Electric Vehicle (EV) Owners

Counter professionals are often responsible for helping customers who may need some extra help purchasing the correct brake parts, so they must understand that brake pad recommendations should be specific to each customer’s vehicle type and driving applications. This is especially important as adoption of electric vehicles has increased in recent years and will continue

BMW X3 E83 Brake Job

BMW’s first attempt at a crossover SUV is what they call a Sports Activity Vehicle (SAV).