Tech Tip: Subaru Parasitic Battery Draw

Tech Tip: Subaru Parasitic Battery Draw

This bulletin provides the diagnostic procedure when checking for excessive battery draw for any Subaru model. Prior to beginning test, be certain the vehicle battery is fully charged and that the battery posts and cable ends are free of corrosion, dirt, sealer and in good condition ....

This bulletin provides the diagnostic procedure when checking for excessive battery draw for any Subaru model.

Prior To Beginning Test:

  • Be certain the vehicle battery is fully charged.
  • The battery posts and cable ends are free of corrosion, dirt, sealer and in good condition.
  • Be sure to record the customer’s radio station and satellite radio station pre-sets as they will be lost during the test, along with any seat memory settings.
  • You may not use an aftermarket 9V memory device in the power outlet to retain any ECU memory.
  • Any aftermarket accessories will also need to be disconnected. These items will affect the test results and may cause false readings or misdiagnosis.

Items Required For Test:

  • Pen and paper for recording radio and satellite radio pre-sets;
  • Digital volt ohmmeter;
  • 10 mm wrench; and
  • 16-gauge bypass wire, about 12 inches long, with proper securing attachments at each end.

Test Procedure:

  1. Remove the battery negative cable.
  2. Connect one end of the bypass wire to the battery’s negative post, then connect the other end to the negative battery cable end. Simply wrapping then twisting the stripped back ends of the bypass wire around the post and terminal will be sufficient. Reinstall the negative cable on the battery post
  3. Wait five minutes before proceeding to the next step. This will allow the system voltage to stabilize. During this time, be sure the glove box door, trunk, tailgate and all vehicle doors are closed and their corresponding lamps are off. Also, be sure that the head lamps, fog lamps and all switches are off. The ignition key needs to be removed, and the doors must be locked (make sure not to lock the keys in the car). Remove the negative battery cable, making sure the bypass wire has not lost contact. If contact is lost, you will need to restart at Step 2.
  4. Make sure your voltmeter is set to milliamp (mA) setting. Connect the test leads of your voltmeter to the negative battery cable and the negative battery post. Remove the bypass wire you installed in Steps 2 and 3 and measure the current draw.
  5. After the five-minute stabilization period, the measured draw should be a maximum of 150 mA. This maximum draw value is read with the key out of the ignition switch.
  6. If your results are greater than the above specification, further diagnosis will be necessary to determine the source of the excessive current draw. This should be done using normal electrical circuit testing until the source of this excessive draw is determined and repaired.
  7. After confirming the repair, the customer’s radio presets and clock time should be reset properly.

Technical service bulletin courtesy of ALLDATA.

For additional information, visit www.alldata.com.

You May Also Like

XL Parts, The Parts House Expands VIP Event Series

The company recently held VIP series events across Houston, Dallas and Orlando.

XL Parts and The Parts House recently concluded its 2026 VIP Event Series with expanded programming across Houston, Dallas and Orlando.

"This year's VIP Event Series represents a significant step forward in how we engage with our team, our vendor partners, and our customers," said President and CEO Vikrant Aggarwal. "We have had the opportunity to create meaningful opportunities to align on strategic growth, strengthen industry relationships, and express our deep appreciation for the partners who drive our business forward."

Toyota Transmission Lost Communication with TCM

A 2011 Toyota Camry equipped with a U660E transmission has come into the shop in default with a trouble code U0101 “Lost Communication With TCM” set.

Understanding Honda’s Variable Valve Timing System

VTEC adds a layer of complexity to any engine, and it does sometimes come with some service bugs, despite Honda’s reputation for reliability.

Toyota RAV4 2006-2013 Alignment

The front suspension is easy to adjust, while the rear needs a little more attention.

2004-2013 Mazda 3 Brake Job

Despite its age, the 2004-2013 Mazda 3 is a popular car you may very well see come through the shop —especially those on the tail end of that year range. Let’s go over the step-by-step brake job process. Related Articles – Servicing Volkswagen Electronic Parking Brakes – Mini Cooper Clutch Replacement – Understanding Brake Pad

Other Posts
OEC Integrates RepairLink, PartsTech Services

Through the integration of RepairLink, PartsTech adds nearly 9,000 OE dealers as well as OE promotional programs.

Autel Integrates Alldata Repair With MaxiSYS Tablets

The integration became available Nov. 1. Existing Alldata Repair subscribers can access it using their current accounts.

Dayco Extends Warranty on Serpentine Belt Kit Line

Dayco announced that it is offering a new five-year, 60,000-mile warranty protection plan on its light-duty serpentine belt kit portfolio.

Worldpac to Open Automated Distribution Center

The 413,000-square-foot facility in Forest Park, Georgia will begin operations in 2027.