Tech Tip: Silencing Dodge Ram's Growling Noise

Tech Tip: Silencing Dodge Ram’s Growling Noise

Noises can sometimes be very difficult to diagnose - especially under the hood and only when the vehicle is in motion. In the case of some 2003 Dodge Ram 1500 2WD pickups equipped with 4.7L and 3.7L V8 engines, a growling or moaning sound may only be heard during heavy acceleration when carrying substantial loads or towing ....

By Rich Diegle
ALLDATA Senior Automotive Editor

Noises can sometimes be very difficult to diagnose — especially under the hood and only when the vehicle is in motion. In the case of some 2003 Dodge Ram 1500 2WD pickups equipped with 4.7L and 3.7L V8 engines, a growling or moaning sound may only be heard during heavy acceleration when carrying substantial loads or towing.

This condition may be cause by the right motor mount contacting the motor mount frame bracket. The noise can be eliminated by installing a rubber isolator between the motor mount and the motor mount bracket.

Diagnosis
Inspect the right engine mount and bracket. If the motor mount is contacting the bracket, there will be witness marks (shiny metal) present on the frame bracket. Perform the Repair Procedure if the witness marks are present.

Repair Procedure
1. Raise the vehicle on a hoist.

2. Place an adjustable jack stand under the engine to support the engine when the motor mount through-bolts are removed.

3. Loosen both motor mount through-bolts. Leave the nut on the left side mount as this bolt will not be removed. Remove the nut on the right side.

4. Raise the engine with the jack stand until the right side through-bolt becomes free. Remove the right side bolt. Raise the engine far enough to clear the frame bracket and allow the isolator pad, (Chrysler P/N 55366020AA) to be inserted.

Insert the isolator on the mount with the Pentastar logo facing the front of the vehicle (see Figure 1).

5. Lower the bracket and align the mount with the frame bracket and push the bolt through the isolator and bracket with the threads at the rear.

6. Install the nut and tighten both through bolts to 115 Nm (85 ft.-lbs.).

7. Remove the jack stand and lower the vehicle.

Written by ALLDATA Senior Automotive Editor, Rich Diegle, an Advanced Engine Performance Certified, ASE Master Technician with an AA Degree in automotive technology and 23 years of dealership and independent shop experience.

Courtesy of ALLDATA.

For additional information on ALLDATA, visit www.alldata.com.

You May Also Like

Electric Power Steering Diagnostics

Load management for steering systems.

In the late 1990s, engineers and OEMs predicted a future where 42-volt electrical architecture would be a standard feature on all new vehicles. This high-voltage system was a solution for the power required for loads such as electric power steering. It got as far as an SAE standard so OEMs and suppliers could implement these systems. What happened? The simple answer is that engineers improved how 12-volt power was managed in the vehicle.

Solving VW False Fuel Pressure Reading

First, verify the customer did not run out of fuel at the time the DTCs were stored.

vw steering wheel squeak
Tech Tips for Dorman’s OE FIX Steering Tie Rod End Assembly

Read the tech note for tips on installation of this unique fix.

Acura Frozen Starter Causes No Start

Why won’t the engine crank after the vehicle has been exposed to precipitation and then freezing temperatures?

Strut Sales

It all comes down to educating the customer about the benefits and asking for the sale.

Other Posts

Beating the Tech Shortage Through Mentoring

How understanding the 80/20 Rule and creative mentoring can make the shortage less threatening.

Nissan Key Will Not Start

Nissan keys use radio frequencies (RF) similar to other everyday wireless devices.

Taking the Fear out of ASE Testing

Spring registration now open; Register by June 30.

Audi EVAP Case Study

Let’s look at some of the things that you should know about Audi EVAP systems before trying to tackle such a repair.