ADAS Calibration Aborts

ADAS Calibration Aborts

Knowing the common “hiccups” can save you time and money.

If you have invested in the fixtures and scan tools to perform ADAS calibrations, you know most systems will walk you through the entire process. But, what happens when you follow the directions and the process still won’t initialize or complete or a malfunction light comes on?

When a calibration comes to a grinding halt, you might feel lost trying to figure out what went wrong. Troubleshooting the problem comes down to knowing the failure, vehicle or fixtures. Often, knowing the common “hiccups” can save you time and money.

There are three types of failures. The most common failure is not being able to start the procedure, or it never completes during a static or dynamic calibration. The next most common failure is a comeback after the driver leaves. Finally, the least common problems are when the vehicle has a false activation of an ADAS warning or corrective action.

Know the Vehicle

Before you start any ADAS calibration, look to see what ADAS features are on the vehicle. In some cases, ADAS systems and features could be optional equipment. There is no sense in trying to calibrate a sensor that is not there.

ADAS is a broad umbrella for many safety systems on a vehicle. ADAS sensors detect the environment around the vehicle. The sensors could be cameras, radar and now lidar. Automakers are improving the sensors and the number of them to add new features and improve accuracy. Then, there are the unseen ADAS sensors, like the brake pedal position sensor and all the ABS and stability control sensors. 

The logic behind most ADAS warnings or corrections is to examine the plausibility of the situation. For example, if the camera classifies an object as another vehicle, it will also use the radar sensor to confirm the vehicle’s path. If only one sensor detects an object, it might just decide the camera has made a false identification, and the plausibility that it is another vehicle is low.

Knowing the ADAS outputs during a dangerous situation is also key. For some early systems, it was just an audio or visual alert. Some newer systems will shake the driver’s seat to alert the driver. More advanced systems can build up brake pressure and apply the brakes if a collision is imminent. Some systems will take further steps with the steering and even close the windows.

Many ADAS features do not become active until the vehicle reaches a specific speed. Pre-collision systems might start working between 5-10 mph, depending on the OEM. Lane departure might not start to work until above 25 mph. The takeaway from this is that a test drive is required after calibration is performed. Simply pulling out of the bay and parking the vehicle in a spot will not allow the vehicle to activate or run a self-diagnosis routine. 

Knowing the speed range limits of these systems is critical if you try to perform a dynamic calibration on the road.

Prep The Vehicle

Before you start a calibration procedure, you need to prepare the vehicle. Missing a step can cause the calibration process to be aborted or calibration to be off. In addition, something as simple as a weak battery can cause problems.

Inspecting the sensors and the vehicle for damage is the first step. Damage to the short- and long-range senor behind the bumper covers or front air dam might not be seen during the initial inspection, but minor collisions can disturb the sensor and damage the mounting points. It could be from hitting a snowbank or parking block. 

You might have to remove the bumper cover to inspect the sensor. The most common symptom is false or delayed activation of the system. If the front radar sensor is pointed up or down, it might detect another vehicle too late, and the correction might be more severe than expected. If the sensor is pointed too far left, it could think oncoming traffic is in the path of the vehicle.

If the rear backup sensors are hit and misaligned, it can prevent the driver from backing up on an inclined driveway. In addition, if the system has a cross-traffic feature, a misaligned sensor can cause errors.

The other key inspection point is to look at the dash for any lights or messages. Never assume a check engine light is only for engine issues; many codes indicate a loss of communication with the different modules on the vehicle. ADAS systems communicate with many modules on the vehicle. Any problems with missing data could cause problems for ADAS calibrations. If the light is on, pull all the codes from the modules.

Alignment angles and Ride Height

An alignment should also be performed to make sure the thrust line is within specifications. As part of the alignment, the steering angle sensor should also be reset. Failing to reset the sensor might cause a steering pull and issues with the electric power steering system. It could also make the vehicle think a vehicle in the opposing lane is coming right at them. On some vehicles, the driver may get a warning or correction.

If the alignment angles have to be corrected, take a look at the ride height. Changes in the ride height and stance of the vehicle alter how the ADAS sensors are pointed.  Check the service information for the fuel level required. The next step is to make sure all the tires are the same and properly inflated. If the tires have different rolling diameters, it can change the body’s height and the aim of the ADAS sensors.

Cameras and Wipers

Before you start with the calibration procedure, make sure the cameras are clean. On newer models, you will have cameras in the windshield, C-pillar and trunk. Wipe down the cameras to avoid any problems. Also, if a radar sensor is covered in mud or debris, clean that off. A layer of dirt can absorb the ultrasonic or radiowaves emitted and received by these sensors.

For ADAS to work, the camera needs a clear view of the windshield. This is why almost every ADAS-equipped vehicle has an automatic or “rain-sensing” wiper system. But, if the system detects too much rain or the system is running at a fast speed, the lane departure or adaptive cruise control will shut down. If the wiper blades are worn out and leave streaks, ADAS features will also be disabled under certain conditions, and the driver may receive a warning that the camera is blocked. 

Troubleshooting your Shop

When setting up the targets to perform a calibration, look at your shop. Lighting is often a key reason why some camera calibrations are never completed. The lighting for calibration should be even and consistent. Shadows cast across a target can prevent a camera from recognizing a target. Windows in doors and skylights can cause shadows. 

Look at the area around the targets. If there is a large pile of old parts or equipment behind the target, it could cause contrast issues for the cameras during calibration.

The most crucial tip for performing any calibration procedures is to follow the steps or prompts on the screen to the letter. Also, confirm the language in the service information or on the screen. Since ADAS is not standardized, acronyms and component terms are not the same from vehicle to vehicle. A PCR and one vehicle might be a completely different part or procedure on another. If the service information has a glossary, use it.

You May Also Like

Tech Tips for Dorman’s OE FIX Steering Tie Rod End Assembly

Read the tech note for tips on installation of this unique fix.

On certain 2021 to 2023 Ford Bronco SUVs, the original tie rods are similar to the diameter and design as those on much lighter passenger sedans, making them susceptible to snapping under steering stresses. Breaks can also occur on Broncos that are used off-road and/or lifted to accommodate larger tires, whether in factory trim or with aftermarket lift kits. The dealer offers a similar tie rod design as a replacement, inviting the same issue again. Our Dorman TA87445RDOE FIX™ kit is engineered to provide a more permanent solution. The kit features many upgrades, including larger outer and inner tie rods than the factory rods, as well as a larger thread interface than the original equipment. In addition to the 2 tie rods, this kit contains 2 steering rack bellows and bellows adapters, and all the hardware for a complete installation on multiple generations of Bronco steering racks. Read the tech note for tips on installation of this unique fix.

Acura Frozen Starter Causes No Start

Why won’t the engine crank after the vehicle has been exposed to precipitation and then freezing temperatures?

Strut Sales

It all comes down to educating the customer about the benefits and asking for the sale.

Beating the Tech Shortage Through Mentoring

How understanding the 80/20 Rule and creative mentoring can make the shortage less threatening.

Nissan Key Will Not Start

Nissan keys use radio frequencies (RF) similar to other everyday wireless devices.

Other Posts

Autel’s ADAS Bay Max Vehicle Lift

Learn how this lift integrates mechanical repair, four-wheel alignment, and ADAS calibration, prioritizing efficiency and space utilization in your shop.

ADAS Calibrations: Limited Space

Babcox Media’s Joe Keene provides a quick overview of many examples that demonstrate ADAS work should be in play for almost everyone.

Key Considerations for ADAS Brake Jobs

As a technician, you could likely carry out a brake job in your sleep, but with automotive technology constantly evolving, what used to be a straightforward service can now require some additional steps and considerations to ensure that your customer’s brakes are in good working order. This is especially true when performing brake service on

Mercedes EQS Service Opportunities

EQ is the EV brand for Mercedes. It is the equivalent of Audi’s Etron.