Tech Tip: Fixing Outlandish Squeaks on Mitsubishi Outlander and Lancer Vehicles

Tech Tip: Fixing Outlandish Squeaks on Mitsubishi Outlander and Lancer Vehicles

Squeaks from the rear of 2002 to 2005 Mitsubishi Outlanders or Lancers, most noticeable when traveling over speed bumps, may be caused by a corroded outer lower control arm bushing. Water intrusion through the control arm bushing seal may allow corrosion, resulting in a squeak during control arm movement. The factory-recommended repair is to replace the parts with updated versions that are designed to prevent water intrusion.

by Eric Seifert
ALLDATA Automotive Technical Editor

Squeaks from the rear of 2002 to 2005 Mitsubishi Outlanders or Lancers, most noticeable when traveling over speed bumps, may be caused by a corroded outer lower control arm bushing.

Water intrusion through the control arm bushing seal may allow corrosion, resulting in a squeak during control arm movement. The factory-recommended repair is to replace the parts with updated versions that are designed to prevent water intrusion.

After test driving the vehicle to confirm the customer’s complaint, confirm that the source of the noise is from the upper or lower control arm (or both).

If the noise is NOT coming from a rear control arm, diagnose and repair/replace the appropriate component(s), as necessary. Do not continue with this procedure.

NOTE: Control arm components on U.S. vehicles are different than those on Canadian vehicles.

Lower Rear Control Arm Bushing:
• 4113A062 (Lancer and Outlander ­ U.S. only)

Lower Rear Control Arm Assembly:
• MR491963 (Lancer ­ Canada only)
• 4113A035 (03-­04 Outlander ­ Canada only)
• 4113A033 (05 Outlander ­ Canada only)

Upper Rear Control Arm Assembly:
• MN100086 (05 Outlander, 04-­05 Lancer 2.4L MIVEC)
• MN100107 (03-­04 Outlander)

Applicable Vehicles:
• 2002-­05 Lancer (except ES models)
• 2004 Lancer Sportback built before: 4/18/05 (U.S.); 9/2/04 (Canada)
• 2003-­05 Outlander built before: 4/18/05 (U.S.); 9/2/04 (Canada)

Service Procedure:
(Review safety procedures contained in ALLDATA Repair before beginning.)
1. On the side of the vehicle where the noise occurs, determine whether the noise occurs at the upper or the lower control arm or both. Use the new parts listed in the introduction of this article.

U.S. Vehicles

• If the noise occurs at the lower control arm, replace the lower control arm outer (pillow ball) bushing.

• If the noise occurs at the upper control arm, replace the upper control arm assembly.

Lower Arm Bushing (Outer Pillow Ball Bushing) Replacement Procedure

• Drive out the old bushings and press­fit the new bushing.

NOTE: After press­fitting, the space between the edges of the bushing outer sleeve and the lower arm should be 3 mm (0.120 inch).

Canadian Vehicles

• If the noise occurs at the lower control arm, replace the lower control arm assembly.

• If the noise occurs at the upper control arm, replace the upper control arm assembly.

2. Test drive the vehicle to confirm the squeaking noise is eliminated.

Written by ALLDATA Technical Editor, Eric Seifert. Eric is an ASE certified Master Technician and Engine Machinist. He is a graduate of the De Anza College Automotive Technology Program, with 20 years of independent shop and parts store experience.

Courtesy of ALLDATA.

For additional information, visit www.alldata.com.

You May Also Like

How to Service the Honda 10-Speed Transmission

The Honda 10-speed transmission is going into its eighth year on the roads, so one may show up in your shop for service.

How to service the Honda 10-speed transmission

With the Honda 10-speed transmission (see Figure 1, above) going into its eighth year on the roads, it’s feasible that one may show up in your shop for service.

(One note: this front wheel drive transmission does not have a typical name; it’s simply known as “the Honda 10-speed automatic transmission” in all OEM materials.)

No Throttle Response in Nissan CVTs: What To Do

We have encountered no-move conditions in Nissan CVTs on several occasions, especially with 3.5L Nissan Pathfinders.

No Throttle Response in Nissan CVTs: What To Do
Older Cars: Using Industry Knowledge in the Shop

What was known about older vehicles and their transmissions by technicians is becoming scarce and nearly lost.

Bringing Down The Bus: Battling A BMW No-Crank

I arrived at the shop and verified the no-crank condition. The dash lit up brightly, but no starter action was forthcoming. Beginning with the basics, I tested power supply at the ignition switch, behind the Car Access System (CAS). This is the module in which the key is inserted. Power and ground was intact; I tested at the starter and found actuation voltage unavailable for starting.

Hyundai TPMS Guide

One difference between Hyundai and other OEM TPMS systems is the decision to place the antennas for the sensors in doors and tailgates.

Other Posts
Honda Fit TPMS Indicator Is On With VSA DTC C0077-78

The cause of the code and light is that the TPMS software may not be properly adapted to driving up or down steady grades.

Hyundai Genesis New Tool For Connector Pin Tension

Detecting excessive female terminal spread can be challenging, especially with micro female terminals.

Tech Tip: Honda Electric Power Steering Sticking and Slipping

While driving at highway speeds, drivers of the 2022-2024 Honda Civic may find that the steering wheel does not automatically return to center.

Tech Tip: BMW Clean Oil Drain Plug

You may encounter an oil drain plug on a late-model BMW (2018 and newer) that is just the cover for the drain.