When Should The Wheel Bearing Flange Be Replaced?

When Should The Wheel Bearing Flange Be Replaced?

The hub flange is ground zero for pulsation problems. Any runout in the flange will be magnified by the rotor. But, when do you replace a flange, stub axle or an entire hub unit? The answer can be confusing and will take some math and a micrometer.

The hub flange is ground zero for pulsation problems. Any runout in the flange will be magnified by the rotor. But, when do you replace a flange, stub axle or an entire hub unit? The answer can be confusing and will take some math and a micrometer. 
 
All flanges have some degree of runout. This is why there are tolerances in the service specification and in manufacturing. Most vehicles can tolerate a certain degree of runout before pulsation is felt by the driver. 
 
A flange may have up to .005” of runout and the bearings may have zero end play or noise. It is impossible to see damage with the naked eye.

This is why measuring with a dial indicator as part of a brake job is important. Damage to the flange is usually found on the backside of the flange where it meets the shaft and inner race. 
How Did Damage Occur?
A flange can be damaged by curb strikes, installation errors or even corrosion. Extreme or catastrophic flange damage due to a curb strike is rare. But, some curb strikes can tweak the flange and cause runout. In most cases, the wheel and knuckle will deform before the flange or stub axle. 
 
If a hub or bearing is over torqued, it can damage the flange and cause runout. It can also damage the bearings and the axle shaft. This type of runout can not be corrected by re-torquing the axle nut. The damage is permanent. 
 
Pitting and corrosion where the rotor mates to the flange can induce runout. If the corrosion is too great, replace the flange or bearing. Also, the flange can be damaged by excessive and uneven lug nut torque. 
  
How Much Is Too Much?
When diagnosing runout in a flange, a few things have to be taken into consideration before replacement. First, take into consideration the vehicle. On a small vehicle, .003” of runout in the flange may be too much. On a full-sized pickup this may be acceptable. 
 

Some OEMs may have a specification and replacement criteria for the flange runout, many do not. Always check for service information. 
Another consideration is the rotor. If you are using an on-the-car brake lathe, there is only so much meat on the rotor to remove to compensate for lateral runout. If too much material is removed, it could create a rotor that is thermally unbalanced. 
 
Most on-the-car brake lathes with automatic runout compensation will not allow the user to continue if the amount of lateral runout is too large. Either the machine will cite an error with the rotor or mounting of the lathe.
 

One option to save a flange is the rotor correction plate or shim. Flange runout can be corrected with tapered shims that are available to correct a runout of 0.003 inch (0.075 mm) to 0.009 inch (0.230 mm).
 
A runout of more than 0.005 inch (0.125 mm) at the bearing flange cannot be corrected by the use of a shim. The combination of rotor and bearing flange could prevent the rotor from being turned. Checking bearing flange runout should be performed after friction surface runout. Change the rotor position 180 degrees on the flange and check runout. If the high spot changes 180 degrees, the rotor could be OK or ready to turn after the bearing is shimmed.
 
Check the bearing endplay. Mark the relation of the rotor to the bearing flange. Mark the rotor high and low runout spots on the rotor friction surface; the low spot marked as zero and the high spot as the maximum value. Mark the high and low runout spots on the bearing flange with the same method and the rotor friction surface.  
 
Once you collected the data, the following comparisons should be made. Compare bearing flange to rotor runout position. If the shim cannot correct the runout, the bearing should be replaced. Check the rotor thickness. 
Replacement 
As a rule of thumb, runout greater than .005” for a light vehicle is a sign that the flange may be damaged or out of specification and further corrective action must be taken. 
 
If all attempts have been made to correct runout and it can’t be brought below .002” or recommended specification, the final option is replacement of the flange, stub axle or wheel bearing hub unit. 

You May Also Like

AUDI Outside Air Temperature Readings

Incorrect readings can be avoided.

With the recent changing of seasons, it is possible to see a 20- to 30-degree temperature change from when the car is parked in the evening and driven again in the morning. Some customers may say they think the ambient temperature is not reading accurately. To achieve a "smoothing" effect of the displayed outside ambient temperature, the value shown does not instantaneously follow the temperature sensor measurement.

Mercedes-Benz ABC Suspensions

The system provides great ride & handling, but it can be complicated to service if you do not have the right training.

Audi TFSI/FSI: Oil Consumption And Carbon Buildup

Technical Service Bulletins can be valuable in helping solve vehicle problems. But sometimes, it takes multiple TSBs to find a pattern failure or the “root cause” of a problem. In the case of the Audi/VW 2.0L Fuel Stratified Injection (FSI) engine introduced in 2006, three problems related to engine carbon and fuel issues are connected

BMW Headlight Service

Taking a guess can get very pricey if you can’t return the part. 

BMW Diagnostics: Low Airflow After Cabin Filter Replacement

Models:  F97 X3 M  F98 X4 M G01 X3 G02 X4 G20 3-Series SITUATION After replacing the microfilter during a previous service, the customer notices that the ventilation system airflow rate is noticeably less. This leads to perceived lower cooling power. The customer may also notice that external odors enter the vehicle. Related Articles –

Other Posts

BMW Cooling System Problems

Let’s take a closer look at this unique water pump, how to replace it efficiently and what other components should be replaced along with it.

Audi Active Suspension Service

The key to servicing these systems is proper information and understanding precisely how these systems operate.

How To Service BMW Tire Monitor Systems

BMW has offered Tire Pressure Monitoring Systems (TPMS) for more than 20 years. These early indirect and direct systems were implemented not to meet the 2007 government mandate but to inform the driver when an expensive Michelin or Bridgestone run-flat tire was deflating. Some 2002 and 2003 models have an indirect system called Flat Tire

VW DSG Maintenance

A DSG transmission is lighter than a comparable automatic with the same number of speeds.