Tech Tip: Solving Lower Ball Joint Removal and Installation Issues

Tech Tip: Solving Lower Ball Joint Removal and Installation Issues

When installing a replacement ball joint in these applications, technicians may note that the new ball joint may not fit tight in the opening of the lower control arm.

Affected Vehicles: Ford Expedition, Explorer, Explorer Sport Trac, F-150, F-150 Heritage, F-250, Ranger, Lincoln Navigator, Mazda B2300, B3000 and Mercury Mountaineer

Problem:
• When installing a replacement ball joint in these applications, technicians may note that the new ball joint may not fit tight in the opening of the lower control arm. The lower ball joint receptacle has been known to experience wear, especially when the ball joint has been replaced several times. If a traditional ball joint is installed in this situation, it will move and shift during operation, which can quickly wear out and damage the control arm, as well as causing unsafe handling issues.

Note: Lower ball joints in these applications are difficult to press out. When removing, an air hammer or chisel is not recommended as it can damage the control arm and the ball joint receptacle. Moog recommends the use of its T40003 Ball Joint Removal Tool.

Solution:
The MOOG K8695T006 (oversized) Ball Joint
The MOOG K8695T006 lower ball joint was designed for ease of installation and longer life.

• The ball joint is 0.006” oversized to fit in worn lower control arm receptacles.

• The snap-ring makes installation easy. The snap-ring in combination with the knurled housing keeps the ball joint securely in place. Use of an appropriate press tool, like the MOOG T40003, is recommended.

• The greaseable design ensures fresh lubrication reaches the bearing surfaces while flushing contaminants, while the all-metal gusher bearing design holds up to severe driving conditions.

Installation Notes:
If opening size is < 1.749”, use K8695T.

If opening size is 1.749”-1.753,” use K8695T006

The T40003 tool is designed specifically for removal of the ball joint on these vehicles. If the incorrect ball joint press receiver is used, you could mushroom the housing of the old ball joint and further enlarge the control arm hole, requiring replacement of the control arm.

Courtesy of Moog Problem Solver Bulletin: 29009

You May Also Like

OEC Integrates RepairLink, PartsTech Services

Through the integration of RepairLink, PartsTech adds nearly 9,000 OE dealers as well as OE promotional programs.

OEConnection LLC (OEC) announced that it is integrating its PartsTech and RepairLink services.

According to OEC, PartsTech currently connects shops to 240-plus aftermarket suppliers, 60-plus tire suppliers, and distributor-sponsored promotional programs. The integration of RepairLink will enable PartsTech to add nearly 9,000 OE dealers across all 50 states and OE-sponsored promotional programs from 14-plus OE brands. Every major part type is now available in a single search, the company says.

Toyota Transmission Lost Communication with TCM

A 2011 Toyota Camry equipped with a U660E transmission has come into the shop in default with a trouble code U0101 “Lost Communication With TCM” set.

Understanding Honda’s Variable Valve Timing System

VTEC adds a layer of complexity to any engine, and it does sometimes come with some service bugs, despite Honda’s reputation for reliability.

Toyota RAV4 2006-2013 Alignment

The front suspension is easy to adjust, while the rear needs a little more attention.

2004-2013 Mazda 3 Brake Job

Despite its age, the 2004-2013 Mazda 3 is a popular car you may very well see come through the shop —especially those on the tail end of that year range. Let’s go over the step-by-step brake job process. Related Articles – Servicing Volkswagen Electronic Parking Brakes – Mini Cooper Clutch Replacement – Understanding Brake Pad

Other Posts
Autel Integrates Alldata Repair With MaxiSYS Tablets

The integration became available Nov. 1. Existing Alldata Repair subscribers can access it using their current accounts.

Dayco Extends Warranty on Serpentine Belt Kit Line

Dayco announced that it is offering a new five-year, 60,000-mile warranty protection plan on its light-duty serpentine belt kit portfolio.

Worldpac to Open Automated Distribution Center

The 413,000-square-foot facility in Forest Park, Georgia will begin operations in 2027.

AISIN Announces New Product Program

Parts available through this program include products in cooling systems, drivetrain, steering, suspension, chemicals and fluids.