Tech Tip: Fuel Filler Necks And Related Check Engine Light Conditions

Tech Tip: Fuel Filler Necks And Related Check Engine Light Conditions

Since the introduction of the OBD II system, manufacturers have continued to improve on the monitoring of evaporative emissions, with the complete evaporative system being under a scrutinized surveillance. Codes like P0440 to P0456 are all related to the fuel vapor control, including leaks.

Since the introduction of the OBD II system, manufacturers have continued to improve on the monitoring of evaporative emissions, with the complete evaporative system being under a scrutinized surveillance. Codes like P0440 to P0456 are all related to the fuel vapor control, including leaks.

Starting early this century, manufacturers have increased the development of fuel vapor retention, preventing the vapors from escaping into the atmosphere. This prompted many changes in the design and location of certain components such as charcoal canisters mounted near the fuel tank.

A fuel tank pressure sensor is used to monitor the pressure decay in the system during the testing and will turn on the check engine light if the pressure decay moves out of specification. Remember that the evaporative system test will not be performed if the fuel level is below a 1/4, as it would cause for too much pressure buildup in the tank or simply would take too much time to build any pressure.

A helpful tool to identify leaks is a smoke-generating machine. During the smoke machine process, loose or broken hoses are usually identified as the main cause of evaporative failures. An additional component has started to surface and is becoming the leading cause of evaporative emissions leaks — the fuel filler neck.

Most fuel filler necks are made of steel and are secured to the fuel tank via a rubber hose. The fuel filler neck is usually enclosed in the rear fender well, where an accumulation of dirt and debris causes the filler neck to rust and leak. These models are hard to diagnose, as the inner fender protection must be removed to get access. Others are totally exposed behind the fender where plashing and road debris erosion removes paint and perforates the filler neck.

The filler cap, which besides not being properly secured after refueling, may cause multiple failures of the system as well. The fuel filler cap may have a defective control valve and prevent pressure hold in the system. Second, the filler neck itself may have rust on the outer seam, which will prevent the cap from sealing properly to the filler neck. On some models, the part where the cap screws on is made of plastic and can be damaged by the fueling nozzle when inserted during refill, which will prevent proper sealing.

All of these situations will cause the check engine light to turn on. Make sure to implement fuel filler neck inspection into your regular vehicle maintenance or during fuel tank removal to prevent comebacks.

Courtesy of Spectra Premium.

You May Also Like

Understanding Mercedes-Benz TPMS

Mercedes-Benz makes the assumption that in the U.S. we adjust our pressure for the number of people and intended speed.

On different Mercedes-Benz models, you will see two types of TPMS systems. Low-line systems do not display individual tire pressures – these systems just monitor inflation and alert the driver if there is an under-inflation or over-inflation problem with one antenna. Mid-line systems display the individual pressures, and some systems have four antennas mounted near the wheel wells.

Toyota Transmission Lost Communication with TCM

A 2011 Toyota Camry equipped with a U660E transmission has come into the shop in default with a trouble code U0101 “Lost Communication With TCM” set.

Understanding Honda’s Variable Valve Timing System

VTEC adds a layer of complexity to any engine, and it does sometimes come with some service bugs, despite Honda’s reputation for reliability.

Toyota RAV4 2006-2013 Alignment

The front suspension is easy to adjust, while the rear needs a little more attention.

2004-2013 Mazda 3 Brake Job

Despite its age, the 2004-2013 Mazda 3 is a popular car you may very well see come through the shop —especially those on the tail end of that year range. Let’s go over the step-by-step brake job process. Related Articles – Servicing Volkswagen Electronic Parking Brakes – Mini Cooper Clutch Replacement – Understanding Brake Pad

Other Posts
OEC Integrates RepairLink, PartsTech Services

Through the integration of RepairLink, PartsTech adds nearly 9,000 OE dealers as well as OE promotional programs.

Autel Integrates Alldata Repair With MaxiSYS Tablets

The integration became available Nov. 1. Existing Alldata Repair subscribers can access it using their current accounts.

Dayco Extends Warranty on Serpentine Belt Kit Line

Dayco announced that it is offering a new five-year, 60,000-mile warranty protection plan on its light-duty serpentine belt kit portfolio.

Worldpac to Open Automated Distribution Center

The 413,000-square-foot facility in Forest Park, Georgia will begin operations in 2027.