BMW Headgasket Replacement

BMW Headgasket Replacement

To service them, you will need the appropriate toolset to lock the crank and camshaft.

The BMW N53 (naturally aspirated) and N54 (turbocharged) engines were among the first BMW engines to come with variable valve timing on the intake and exhaust camshafts. The N53 and N54 straight-six has unfairly earned a bad reputation for reliability with technicians due to timing chain and variable valve timing problems. The reputation comes from owners not keeping up with oil changes and it is difficult to check engine timing.

BMW VANOS Actuators and Solenoids

The latest versions continuously adjust the position of the intake and exhaust camshafts for better power, efficiency and idle performance. The keyword to remember for a late-model VANOS system is that it works “continuously,” and not just under specific rpm ranges.

To service them, you will need the appropriate toolset to lock the crank and camshaft. You will also need a scan tool and a scope to observe the crankshaft and camshaft signals to accomplish more advanced diagnostics.

VANOS

Some newer systems can change the camshaft timing by as much as ±72 degrees. Dual-VANOS systems operate at all engine speeds. At lower engine speeds, the VANOS system opens the valves later during the intake stroke, increasing the vacuum and scavenging effect generated by the piston traveling downward in the cylinder. This improves idle quality and smooth power tip-in from a stop. As the engine rpm increases, the valves are opened earlier, enhancing torque as rpm increases. At higher engine speeds, the valves open later for full power delivery so the scavenging effect of the exhaust leaving the cylinder can pull more air into the cylinder. Hot rodders call this “valve overlap.”

The system can augment and even eliminate the EGR valve by allowing some of the exhaust gas to remain in the combustion chamber to control combustion temperatures and NOX emissions.

Also, the camshaft position is changed to reduce engine warm-up times by allowing some unburned fuel to reach the catalytic converters. When the VANOS system on the N53 and N54 is not working, the most common symptoms are poor idle quality, reduced power and poor fuel economy. These symptoms are common to any other variable valve timing system, as well.

How Does VANOS Work?

Like many variable valve timing systems, VANOS uses oil pressure-powered actuators to move the camshafts. The actuators need a consistent supply of oil for the correct viscosity, pressure and volume.

VANOS Camshaft Phaser

The N53 and N54 use a conventional cam phaser with internal chambers that hold pressurized oil that change the position of the camshaft.

BMW N53 and N54 use an oil control valve like a lot of other variable valve timing engines. The solenoid is actuated by a pulse-width modulated signal.

If the oil is contaminated or is the wrong viscosity, the system can become sluggish. If the oil pressure can’t move the camshafts to the target positions in a specified time, the camshaft position sensors will sense it and set a code.

When oil pressure is not present, the camshafts go to a fully retarded position and are locked in place by a pin. A code will be set if the actuator and camshaft do not return to the correct position, because they are hydraulically jammed due to oil pressure leaking past a seal.

If you are trying to scope a crankshaft and camshaft waveform, disconnect the oil control valve. If this is not done, the waveform might look like the timing is out of sync because the engine will be adjusting the camshafts.

What Goes Wrong With N53 And N54 VANOS Systems?

The two most common failures for a VANOS system are related to the quality of the oil. The most common failure is when the O-ring seal on the piston wears out and allows oil pressure to move between the two chambers. This causes the actuator to be stuck or hydraulically jammed in either the full advance or retard positions.

When this happens, the actuator can’t fight the pressure exerted on the camshaft by the valve springs. This can cause a rattling noise at startup and idle.

If the oil is the wrong viscosity, it can cause the corrections to either retard or advance – in other words, to lag or happen too quickly. These changes take place in milliseconds. Depending on your scan tool and whether you can pull BMW DME or OBDII codes, the description may include the words jammed, stiff or lagging.

The engine will factor in the oil and coolant temperature into the time allowed for the actuation. If you have any codes related to these sensors, you might want to resolve these issues before troubleshooting the VANOS system.

Remind your customers that the quality of the oil in both engines matter to the life of their timing chains. BMW recommends a high-quality 5W-30 or 5W-40 that is fully synthetic and meets the BMW Longlife-01 FE specifications. These oils are formulated around the extended oil change interval. When a low-quality oil is used, it can break down before the oil change interval and accelerate wear on the links and pins of the timing chain.

You May Also Like

VW/Audi PCV Service

The PCV valve regulates the flow of gases from the crankcase.

Positive crankcase ventilation (PCV) systems have been on just about every vehicle since the late 1960s. The systems route crankcase vapors and droplets into the intake manifold so they are burned in the combustion chamber or catalytic converter. 

The PCV valve uses the vacuum from the intake manifold to regulate the flow of gases from the crankcase. The pintle or ball inside the valve moves in response to the pressure difference between the crankcase and the intake manifold. The valve is typically located between the throttle body and cylinder head on a runner for the intake manifold.

Volvo Engine Service

There are many combinations for the Volvo modular engine.

Servicing Mercedes-Benz AMG Brakes

Take a look at some of the things you need to know in order to service the brakes on a Mercedes-Benz AMG vehicle.

AUDI Outside Air Temperature Readings

Incorrect readings can be avoided.

Carbon Deposits and Direct Injection Engines

The primary cause of these problems is that fuel and added detergents are not hitting the back of the intake valves.

Other Posts

Mercedes-Benz ABC Suspensions

The system provides great ride & handling, but it can be complicated to service if you do not have the right training.

Audi TFSI/FSI: Oil Consumption And Carbon Buildup

Technical Service Bulletins can be valuable in helping solve vehicle problems. But sometimes, it takes multiple TSBs to find a pattern failure or the “root cause” of a problem. In the case of the Audi/VW 2.0L Fuel Stratified Injection (FSI) engine introduced in 2006, three problems related to engine carbon and fuel issues are connected

VW Electric Parking Brake Service

Unapproved methods will set malfunction codes and, worst-case, you could damage the unit.

BMW Headlight Service

Taking a guess can get very pricey if you can’t return the part.