Tech Tip: Eliminating Toyota Air Conditioning Evaporator Odor

Tech Tip: Eliminating Toyota Air Conditioning Evaporator Odor

A musty odor may be emitted from the air conditioning system of some vehicles that are usually operated in areas with high temperature and humidity. It’s most noticeable when the air conditioner is first turned on after the vehicle has been parked for several hours.

A musty odor may be emitted from the air conditioning system of some vehicles that are usually operated in areas with high temperature and humidity. It’s most noticeable when the air conditioner is first turned on after the vehicle has been parked for several hours.

The odor could result from one or more of the following conditions:

1. Blockage of the evaporator housing drain pipe, resulting in a buildup of condensate.

2. Microbial growth in the evaporator, arising from dampness in the evaporator housing where the cooling airflow is dehumidified.

To address excessive air conditioning evaporator odor, check the evaporator housing drain pipe for blockage. If no problems are found, the evaporator and housing should be cleaned and disinfected using the following service procedure.

While this procedure may be used on any Toyota vehicle, specific details for the 1997-and-older SXV/VCV10 Camry follow.Caution: Wear safety glasses, protective mask and gloves while working with the freshener.

Service Procedure:
1. Parts removal.

a. Pull down the carpet from the center console as indicated by the bigger arrow in Fig. 1.

b. Remove the plate on the side of the heater unit using steps (1) and (2), indicated with bigger arrows to show direction in Fig. 2.

Caution: Do not bend the cable; the plate will be reused.

c. Remove the blower resistor.

2. To clean the evaporator, follow the general procedures at the beginning of this bulletin. Also see Fig. 3.

3. Parts reinstallation.

a. Reinstall the plate on the side of the heater unit using steps (1) and (2), indicated with bigger arrows to show direction in Fig. 4.

Caution: Confirm that the plate is secure.

b. Restore the carpet to its original position, taking care not to bend the cable.

Technical service bulletin courtesy of ALLDATA.

For additional tech tips, visit www.alldata.com.

You May Also Like

Today’s Fuel Pressure Diagnostics

Direct injection pressure is measured with sensors, and the signals are used to determine pump speed and/or volume.

Ever since the fuel pump was moved to the fuel tank, fuel pressure replaced the float height as a measure of fuel system health and performance. Checking the height of the float might have required some disassembly or special tools to bend the arms of the float.

When the shift was made to port or throttle body fuel injection, all a technician needed to diagnose a fuel problem was a set of “noid lights,” a fuel pressure gauge and maybe a multi-meter. Measuring the fuel pressure typically required checking the pressure at idle and under load. Most of the these tools can’t be used on the high pressure side of a direct-injection system because of higher pressures and changes in the injector location and technology. 

ADAS Calibration Tips

Here are 10 tips to follow during ADAS Calibration.

ADAS Calibration Aborts

Knowing the common “hiccups” can save you time and money.

Fuel Pumps and Cranking

Diagnosing the problem comes down to understanding what causes a loss of fuel pressure.

Electric Power Steering Diagnostics

Load management for steering systems.

Other Posts

Don’t Miss The April Digital Edition of ShopOwner

The April issue includes technical and management content and is free to download.

Now Available – March’s Digital Edition of ShopOwner

The March issue includes technical and management content and is free to download.

Now Available – February’s Digital Edition of ShopOwner

February’s issue includes technical and management content and is free to download.

How To Service BMW Tire Monitor Systems

BMW has offered Tire Pressure Monitoring Systems (TPMS) for more than 20 years. These early indirect and direct systems were implemented not to meet the 2007 government mandate but to inform the driver when an expensive Michelin or Bridgestone run-flat tire was deflating. Some 2002 and 2003 models have an indirect system called Flat Tire