The Volkswagen Tiguan is a compact SUV built on the A5 platform that is shared with the Golf and Jetta.
Booster Problems
On the turbocharged models, the brake booster uses a vacuum pump. If the vacuum pump is failing, the customer may notice a hard brake pedal. The customer may even comment that the pedal changes as the engine warms up.
The seals are what fails on the pump. The pump is driven off the camshaft, and it is located above the transmission. Often there will be an oil leak that looks like a rear main seal issue.
Rear Brakes
The rear brakes on some Tiquans may wear out before the front brakes due to electronic brake distribution. The system uses the rear brakes more to minimize nosedive during normal braking events. For the driver, the system makes the Tiguan feel more composed when stopping for a traffic light.
Volkswagen equipped its Tiguan models with Electronic Parking Brake (EPB) technology. If you are replacing the rear pads, it will require a scan tool to retract the rear caliper pistons. After the piston is reset, you may need to reset the piston further with a clamp to fully retract the piston.
EPB allows the vehicle to engage or disengage the parking brakes at the touch of a button or a command from a module. EPB sets the parking brake when the keys are removed from the ignition. This prevents the vehicle from rolling and lurching when the driver’s foot is removed from the brake pedal and the parking pawl is engaged.
Auto Hold
All Tiguans are equipped with Auto-Hold. When the car is braked to a standstill, Auto-Hold retains the last-applied braking pressure with the ABS modulator. If the ABS wheel speed sensors detect any rolling, the braking force is automatically increased until the car comes to a standstill again. As soon as the driver presses the accelerator again and, in the case of manual gearboxes, releases the clutch, Auto-Hold releases the brakes. This feature also works well in stop-and-go traffic on hills.
The system can be turned on or off manually on 2010-2011 models with a button next to the parking brake button. On 2012 models, the system is on all the time. But, it can be disabled using the driver information display menus. For the system to work, the seatbelt must be fastened, and the doors must be closed.
If the brake pads are worn, or the caliper is seized, the driver may comment that the brakes drag or do not smoothly disengage after a hill hold event.
Take It Easy With Pressure Bleeding
When pressure bleeding an ABS braking system, be sure not to exceed 1 bar (14.7 psi) of pressure. Pressure over 1 bar will cause the change-over valve in the EDS unit (traction control valve in the modulator body) to close, which will not allow the inner circuit of the brake system to bleed.
Pulsation Solution
Volkswagen owners may complain of a pulsating brake pedal when applying the brakes at highway speeds. The pulsation may also be felt as a vibration in the vehicle body, or the steering wheel may shake. The cause of these issues may be improperly machined brakes and lateral runout that was not eliminated. The condition may not be felt until several months after the brakes were serviced when the rotors were replaced. To correct the problem, measure the rotors for runout and thickness variation and correct with an on-the-car lathe. Runout should be below .002″. You may want to try different positions on the flange to reduce runout if you do not have an on-the-car brake lathe.
Creaking While Braking
Some Tiguans may exhibit a creaking noise that originates in the front suspension while braking hard or going over large bumps. The source of this noise could be the forward inner control arm bushing. To confirm if this is the issue, raise the vehicle and remove the wheel on the suspected side. Disconnect the lower control arm at the ball joint and move the arm up and down, checking for noise at the forward bushing.
No Start
The brake pedal must be depressed in order to start Tiguans with automatic transmissions. If you see a Tiguan with a no-start condition in your shop, check the brake pedal position switch. Use your scan tool to confirm the status of the switch.
