Selling Shocks and Struts

Selling Shocks and Struts

Selling shocks and struts can be difficult.

One ride control manufacturer estimates that 80 percent of vehicles in junkyards still have their original shocks or strut units. Part of the reason is that selling shocks and struts is difficult. It is an item that, when it wears, doesn’t cause the vehicle to stop running. When it does wear, the driver is usually not aware of how bad it really has become.

But, it’s an item that can make a distinct difference in vehicle performance and resale value that the customer will really appreciate.

Often, you are your own worst enemy when selling ride control and it happens to most salespeople; over time they become apathetic to selling ride control products to the customer. It is a cycle with three phases as the salesperson starts to speak no evil, hear no evil from the technician and eventually sees no evil when it comes to recommending ride control replacement.

The first phase of this cycle starts with just listing the recommendation and estimate for shock or strut replacement on the repair order and maybe mentioning it casually to the customer during the sales process. This means that the salesperson will invest very little time, effort and emotions. The recommendation becomes more of a “feeler” question, rather than a real sales proposal.

The second phase starts when the salesperson starts second-guessing if he or she should even write the estimate on the repair order at all. They may base their guesses on stereotypes and assumptions. But, chances are, they are wrong.

The third phase is the most destructive to sales. This is where the salesperson rationalizes that the time spent trying to sell the customer ride control can be used for easier items that are guaranteed to sell. This does not only a great disservice to the shop, but is a greater disservice to the customer.

It takes mental and physical tools to break this self-defeatist cycle. Also, turning this apathy into enthusiasm requires a methodical approach that goes further than incentives like vacations, point systems or t-shirts. It requires a proper inspection of the vehicle and communication with the customer.

Inspection

The first step in selling ride control is the inspection process. A visual inspection of the shocks and struts can tell you a lot about the state of the ride control units. If possible, visual inspections should be performed before the test drive. This is a chance to make sure the vehicle is road-worthy before you put your own life at risk. Also, always make sure that there is enough gas in the tank. 

Communication

A complete inspection lays the groundwork for excellent customer communications and increases the possibility of a sale. The results of the inspection can help personalize the sales pitch to the individual customer. 

The following is an example of how a note on an inspection form can provide so much more than a simple “recommend new shocks and struts.”

Salesperson: “On the test-drive, the technician noticed excessive nose dive during braking and increased body roll while turning. Also, we noticed humming coming from the rear that was caused by uneven wear of the rear tires.”

Customer: “I guess it’s not exactly performing the same as it was when new and that humming noise was starting to annoy me.”

Salesperson: “New struts can help return the vehicle to like it was when it was new. Also, they can prevent future uneven wearing of your tires.”

In this simple interchange of information, the details gained in the test-drive helped to identify and define the value of new ride control components to the customer. Furthermore, the information given to the customer helped to create a tangible need that they can relate to on “why” the service should be performed. All of this was done without going into techno speak.

Even if the customer does not buy today, this sales approach and pitch will likely stick with the consumer longer than the generic “recommend new shocks and struts.” This means that they might be back and your efforts will not be in vain.

You May Also Like

Drilled and Slotted Rotors

There’s real science behind the location of holes, slots and grooves in today’s brake rotors. Plus, they look great too.

A brake rotor absorbs and dissipates the heat energy generated by friction. How well the rotor can absorb and then release it into the surrounding air will determine the efficiency and capacity of the brakes.

The design of the rotor determines how it can handle the heat. On vented rotors, the thickness of the plates and how well air flows through the vanes helps to transfer heat to the surrounding air. Curved-vane designs on some vented rotors help to pull air through the center of the rotor to the outer edge and act as a pump. For curved vanes to work, they must be mounted on the hub in the correct direction, just as a directional tire must be mounted on the right wheel.

Laying Out Your Shop for ADAS/EV Repairs

With so many vehicles equipped with some form of ADAS, rethinking your electronics layout or plan might be in order.

Chassis Diagnostic Procedures

The secret is to be quiet & listen, as the customer will tell you almost everything relevant to the repair you need to know.

Air Ride Suspension Diagnostics

The key to understanding the embedded logic of air ride systems is using service information.

Mercedes Airmatic Suspensions

Diagnostic tips to aid your repair efforts.

Other Posts

ZF Expanding SACHS CDC Shocks, TRW Line

ZF Aftermarket also plans to release additional CDC part numbers in Q1 of 2024.

FCS Adds New Part Numbers

FCS released 73 new numbers in the September release.

TPMS Curve Balls for European Vehicles

You May Think You Know the Cause of a TPMS Problem, Until One Car Defies It Related Articles – CVT Transmission Service – Chassis – Ride Control Diagnostics From Tire Wear – Charging For TPMS Service When you think you know everything about tire pressure monitoring systems (TPMS), there will be a car or truck

CVT Transmission Service

Like any automatic transmission, the condition and level of fluid in a CVT unit will determine the performance.