GLOW PLUG PROBLEMS
If the glow plug system is not working correctly, the most common symptom is typically hard cold starting, which may be accompanied by a rough cold and/or white smoke (unburned fuel vapor) in the exhaust. Just remember that these same symptoms can also be caused by other things such as incorrect injector timing, worn or clogged fuel injectors, or poor fuel quality during cold weather.
The resistance of the glow plugs is critical for proper heating and operation. The resistance of the glow plugs will change as they age, but as long as they stay equal and do not exceed specifications (typically 0.5 to 1.0 ohms), they should continue to function normally. Also, the wiring harness and connectors that supply voltage to the glow plugs must be tight and corrosion-free.
On the newer VWs, the onboard diagnostic system monitors the operation of the glow plug system, and may set one or more fault codes if a problem is detected.
On the older VW prechamber non-TDI diesel engines, a problem in the glow plug system will often set a P0380 fault code. Unfortunately, there are no additional codes on these applications to help you figure out where the problem is, or which glow plug may be at fault.
On the newer diesels, the diagnostics is better.
There are more codes, including ones for individual glow plugs:
P0671 – Cylinder 1 glow plug circuit
P0672 – Cylinder 2 glow plug circuit
P0673 – Cylinder 3 glow plug circuit
P0674 – Cylinder 4 glow plug circuit
P1616 – Glow plug indicator lamp circuit shorted to positive
P1617 – Glow plug indicator lamp circuit shorted to ground
P1618 – Glow plug relay shorted to positive
P1619 – Glow plug relay shorted to ground
P3000 – Glow plug indicator lamp circuit on CAN bus fault
When glow plugs fail, the heating element inside typically burns out and goes open. Testing the glow plug with an ohmmeter (with the wiring harness disconnected and power off) will show if the plug has any resistance. Zero resistance would tell you the glow plug has burned out and needs to be replaced. A good glow plug should have a resistance between 0.5 to 1.0 ohms.
In rare instances, a glow plug may short to ground when it fails. Because the glow plug circuit is a high-amperage circuit, a shorted glow plug will overload the circuit and may cause the fuse (or fusible link on older VWs) to blow.
Here’s a tech tip from the TDIclub.com website: If the Check Engine light comes on approximately 30 seconds after starting the engine (and there are no obvious driveability problems other than hard starting), the cause may be a bad glow plug or a fault in the glow plug circuit. If you find a “glow plug monitoring” fault with a VAG-COM or other scan tool, remove the wiring harness from the glow plugs and measure the resistance between each glow plug terminal and the engine block. All four glow plugs should measure between 0.5 to 1.0 ohms, with no more than 0.2 ohms difference between all of the plugs. If any glow plugs are outside this range, or vary more than 0.2 ohms from the others, consider replacing all four glow plugs with new ones.
Also, check the main glow plug fuse (it’s visible under a small clear plastic cover in the engine compartment usually near the battery or firewall). If the fuse is okay, and the glow plugs pass a resistance check, the most likely problem would be a poor electrical connection between the harness and the glow plugs. Remove the glow plug connectors and clean the contacts, or replace the harness. VW usually recommends replacing the glow plug relay, but only in rare instances does the relay go bad. Volkswagen has a special glow plug tester, VAG 1527B, for testing the glow plugs. To use the tester, unplug the connector from each glow plug, attach the tester positive lead to battery positive, and the negative lead to the glow plug. If the LED on the tester lights up, the glow plug is okay. If the LED on the tester does not light up, replace the glow plug.
You should also test to see that the glow plugs are receiving voltage when the ignition is turned on, and that the voltage continues during cranking and for a short time after the engine has started. No voltage to the glow plugs would indicate a bad control module, relay, fuse or wiring fault.
Another way to quick-check the glow plugs without having to use a voltmeter or ohmmeter is to use an infrared thermometer (Note: This works only on a cold engine). Cycle the ignition on and off a couple of times to heat up the glow plugs. Then aim the infrared thermometer at each glow plug so see if all the plugs are generating heat. If you find a cold plug that isn’t heating up, the glow plug or wiring connector is bad and needs to be replaced.
GLOW PLUG REPLACEMENT
The worst thing that can happen when a glow plug burns out is for the tip to break off inside the engine. The tight clearances in the combustion chamber don’t allow any room for chunks of metal to bounce around. This may damage the piston, valves or cylinder head.
Sometimes the tip of a glow plug will mushroom when it fails, making it nearly impossible to remove. Replacement may require removing the cylinder head and drilling out the glow plug. Thread repairs may also be required depending on what’s needed to extract the old plug.
In most instances, the glow plugs can be changed just like a spark plug. Use a deep well socket to unscrew the old glow plugs and to install the new ones. Be careful not to overtighten the glow plugs or you may damage the glow plug or strip the threads in the cylinder head. Thread the glow plug in by hand, turn it a couple of times to make sure the threads are aligned properly, then hand-tighten to the recommended torque (15 Nm or 11 ft.-lbs.). The threads on the glow plug can be lightly coated with anti-seize to make future replacement easier.
Also, compare the old and new glow plugs before you install the new ones to make sure they are the same length. If the replacement plugs are too short on a TDI engine, they won’t extend into the combustion chamber to provide adequate heat. And if they are too long, they may hit something.
The part number for Bosch glow plugs that fit the 1996 to 2007 1.9 TDI engines is 0-250-202-022. The part number for the glow plugs that fit the 1979 to 1996 diesel engines is 0-250-201-032.
WEIRD STUFF
If the glow plug indicator light on a TDI diesel flashes while driving, it doesn’t indicate a fault with the glow plug system. For some reason, VW decided to use the glow plug light as a “bulb out” indicator lamp if a brake light has burned out. A bad brake light switch can also cause the same thing to happen. Wouldn’t it have been less confusing to warn the driver with a “lamp out” light or icon? Go figure.
The vehicle owner may also complain of clicking noises coming from the vicinity of the glow plug relay located in the fuse panel near the base of the steering column. The noise is from the relay switching on and off as supplemental heat is used during engine warm up to reduce emissions. The high current drawn by the glow plugs may also cause the lights to dim slightly when the relay clicks on. But don’t worry, VW says this is normal.
