Understanding Diesel Exhaust Filters

Understanding Diesel Exhaust Filters

The Diesel Particulate Filter (DPF) is a ceramic filter that has thousands of tiny channels or honeycomb-shaped openings that trap the soot onto the channel walls and prevent the particulate matter (down to 1 micron) from exiting out the tail pipe.

Diesel Exhaust Filter
The Diesel Particulate Filter (DPF) is a ceramic filter that has thousands of tiny channels or honeycomb-shaped openings that trap the soot onto the channel walls and prevent the particulate matter (down to 1 micron) from exiting out the tail pipe. The honeycombed inner structure is covered with a layer of a chemical catalyst that contains small amounts of precious metals, usually platinum or palladium.

To reduce the particulate matter or soot from the exhaust, you need to raise the combustion chamber temperature high enough to reduce the PM’s from forming. NOx is formed when the combustion temperatures exceed 3,200°F (1,800°C), and the amount of oxide formed depends not only on the temperature, but also the length of time the heat is applied. However, raising the combustion chamber temperature higher inadvertently raises the amount of NOx that’s formed. This is even worse for the environment than the soot.

Diesel cars and trucks manufactured after 2009 must have a DPF, and in some cases, a Selective Catalysts Reduction (SCR) system. These components work together to reduce, and when working properly, remove all of the harmful NOx and soot from the exhaust. Not only does this help the environment, it also creates a much cleaner engine. Engine oil doesn’t get as dirty as fast as it would have without all of these systems in working order. Less soot mixed with the engine oil means less of that gritty carbon forming in the oil galleys and other moving parts. This increases the life of the engine at the same time it cleans the air.

The drawback to all of this is that the DPF needs to be cleaned regularly. The soot particles attach themselves to the lining of the DPF while the engine is running. At the same time, the filter is slowly clogging with the very particulates that it’s designed to remove from the exhaust. This process of cleaning the DPF is done through a process called regeneration. There are several different methods used by various manufacturers to clean the DPF.

Passive Regeneration
Passive self-regeneration is completely transparent to the operator and does not affect the machine’s operation or performance. The only indication when a passive regeneration cycle has been activated is either an exhaust temperature warning light indicating the exhaust temperature is higher than normal or a message stating a regeneration cycle is in process, or both.

Active Regeneration
Active self-regeneration occurs when there is not sufficient heat in the exhaust to convert the PM being collected in the DPF. The active regeneration is self-activated by the PCM based on various inputs. The PCM sends a command to raise the exhaust temperatures by adding a small amount of injected raw fuel upstream of the DPF. The chemical reaction of the precious metals in the DPF and the raised exhaust gas temperatures oxidizes the PM from the filter.

Stationary (Parked) Regeneration
Stationary, or parked, regeneration is the same as active regeneration but takes place while the vehicle is not being driven. This is either driver induced or done with a scan tool. There are times when the driver will need to perform a manual or “parked” regeneration on the side of the road. This may be because they canceled an earlier regeneration, or an automatic regeneration had started, but was interrupted. In some cases, the regeneration is “forced” onto the driver for ignoring an earlier request to perform a parked regeneration by causing the vehicle to go into limp mode. A lot of times, a warning light or message will tell the driver to pull over and begin a parked regeneration. This usually involves the driver setting the parking brake and engaging a switch to start the process.

Stationary (Parked) Regeneration Precautions
Due to the high heat created during the regeneration cycle, when performing a parked regeneration or a scan tool-induced regeneration cycle, follow these simple rules to avoid any outside interference. Stay clear of combustibles and people.

Filter Failures
Some diesel exhaust filter failures are a result of not allowing the regeneration to take place. This will inadvertently clog the DPF to the point that replacement is the only option. Although it can be cleaned to some degree, a portion of functionality is still lost due to the severity of the restriction. Another problem is when it is in regeneration and the excess heat combined with the clog causes the metal casing of the DPF to expand and rupture. Which, of course, means the only solution is to replace the DPF. The DPF requires professional cleaning every 150,000–250,000 miles or 5000 hours.

Regeneration Monitoring
On some vehicles, the monitoring is done by way of a pressure sensor that measures the input and output pressures of the DPF. Others use mileage or an engine hour counter. On most vehicles, there is a way to shut off the regeneration process if you are in a situation where raising the exhaust system’s temperature could cause a fire. But, don’t leave it off or permanent damage can be caused to the DPF.

Regeneration
Regeneration can only happen when the conditions are within the preset specifications for that motor and manufacturer’s needs. In general, most regeneration cycles are handled without the driver knowing they are taking place. The regeneration process occurs by raising the temperature of the DPF to around 1,100°F (600°C) and enough oxygen is provided directly to the DPF. Some systems will inject extra fuel into the cylinder on the exhaust stroke which effectively sends hot gasses into the oxidation catalyst of the DPF, raising its temperature sufficiently to cause the carbon to react with the excess oxygen that was also provided. Other systems rely on a heating element just in front of the DPF to raise the temperature.

The regeneration process will continue until the pressure differential across the DPF (input and output) drops to an acceptable level. Should the driving circumstances change, for instance, the car comes to a halt and the regeneration is abandoned until the conditions once again become suitable. Regeneration can be a noisy affair, as the engine revs up to 4,000 RPM for four minutes or more, then goes to 2,000 RPM for an additional four minutes or more. When the regeneration has completed, the vehicle will return to its normal idle, and the service light will go back off.

Regeneration Problems
Problems arise when successive regenerations are abandoned, and the soot levels build to a point where the DPF clogs and can’t be regenerated on its own. Short trips and stop-and-go traffic might not allow the DPF to get up to temperature. When this happens, the driver is notified by a flashing DPF warning light. If the warning light is ignored, then a second warning appears which can cause the vehicle to go into limp mode. In limp mode, the vehicle will not operate over 5 or 10 mph and will remain that way until it has been properly serviced using a scanner to perform the regeneration process.

Selective Catalytic Reduction (SCR)
SCR is an alternative to the EGR and addresses the same issue of reducing the NOx contaminants. This system uses a solution of 32.5% urea and 62.5% denatured water called Diesel Exhaust Fluid (DEF). This blue fluid is contained in a separate holding tank that is injected into the exhaust. When the urea mixture meets the hot exhaust gasses, it decomposes to ammonia (NH3) and CO2. The ammonia then reacts with oxides of nitrogen in a second catalytic converter to form a harmless output of nitrogen and water. The advantage is not only a reduction in NOx, but a reduction in the use of the EGR. This means a more efficient combustion, a reduced PM output and improved fuel consumption.

You May Also Like

AC Service – R1234yf

With a few simple steps, you can ensure that your A/C machine is properly maintained and ready for the upcoming A/C season!

Summer is just around the corner, and this is a perfect time to get your air conditioning machine serviced before the busy A/C season hits your garage bays. As the summer winds down and we move into the cooler months, most A/C machine usage winds down as well, with the machine sitting idle for longer periods of time, often unserviced at the end of the season. Now is the perfect time to get it ready to prevent any unwanted “downtime” from a machine that wasn’t serviced. Let’s look into what you can do to get your equipment ready.

Ignition Coil Output

To see inductance inside the primary windings, use an amp probe placed around the positive wire for the ignition coil.

Compressor Oil for R1234yf

Working on R-1234yf systems is not that different from the R-134a variety.

Turbochargers on Minis

No matter if it is a BMW or MINI, when the engine stops turning, the oil flowing to the turbocharger stops.

How Extended Interval Oil Filters Have Been Improved

Over time, the oil filter can collect enough contaminants to become restricted. Here’s why new filters are better.

Other Posts

AC Condensers

The characteristics that make the parallel-flow condenser so efficient are among its major drawbacks as well.

Lifter Deactivation

The area of contact between the lifters and cam lobes is the highest loaded surface inside an engine.

Mercedes-Benz AC Service

Here’s what you need to know about R-1234yf refrigerant in Mercedes-Benz vehicles.

Battery Charging and Diagnostics

Here are six tips to use when diagnosing a vehicle with a dead battery.