Today's Fuel Pumps Operate Differently Than In The Past

Today’s Fuel Pumps Operate Differently Than In The Past

Understanding fuel pressure and volume is more complicated thanks to fuel injection and other modern technology.

The fuel requirements for an engine were easy to understand back in the days of mechanical fuel pumps. The faster the engine turned and as the level in the fuel bowls dropped, more fuel became available for the circuits in the carburetor.

As fuel injection took over, the first electric fuel pump circuits were just a relay and fuse on the power side and the ignition switch on the control side. Control over the fuel pressure was performed with an analog regulator that adjusted for loads with a vacuum signal.

The fuel pump operated at full battery voltage no matter the load on the engine. This is not good for the life of any electric pump and caused significant noise inside the vehicle. It also required a return line to the fuel tank, which presented many difficulties to the EVAP system for detecting small and large leaks.

The earliest effort to improve fuel pump life was to install a series of ballast resistors. As the load on the engine changed, the resistor would be switched. It worked a lot like a resistor motor controller for a blower motor.

The regulator on the fuel rail not only controlled fuel pressure but volume by controlling the flow of fuel with a diaphragm, springs and vacuum. 

The major shift happened when fuel pumps began to be controlled with pulse-width module voltage. The fuel pump is driven by a signal that changes the power to control the speed of the motor and pressure delivered to the fuel rail during the duty cycle. The duty cycle is the measured period of time it takes for a signal to complete an on-and-off cycle expressed as a percentage. On some vehicles, you can view the percentage with a scan tool. 

The driver for these fuel pump circuits is typically part of the engine control module. As engine loads and fuel trims change, the duty cycle increases or decreases.  

Manufacturers have moved the driver for the fuel pump to modules in the rear of the vehicle. Some manufacturers moved the control of the pump to a rear electronic module; some moved it to a dedicated fuel tank module that also performs EVAP control.

As the control for the fuel pump moved to modules, codes for fuel pumps became more common. Some of the most common codes you will see are codes for the fuel pump circuits. These typically indicate that the circuit is open or the voltage is too high or low which indicates a short or high resistance in the circuit. Some of these codes are generic, but if the module is separate from the engine control module, you could be dealing with manufacturer-specific codes.

The module that drives the fuel pump is typically looking for data PIDs from the engine. The data PID for fuel pressure can be critical in a diagnosis of a fuel pump and can save you from hauling out the fuel pressure gauge and the assorted fittings to make a connection. Also, some vehicles have eliminated the test port on the fuel rail. But how do you know if the fuel pressure sensor is bad?

The fuel pressure sensor usually has three wires and operates on five volts. As the fuel pressure increases, the resistance changes. The sensor monitors fuel system pressures and the performance of the pump. If the sensor is not getting a clean five volts, the voltage on the signal side will change. On some systems, this could cause the pressure to read lower than normal and creates some fuel pump performance codes.

Observing the fuel pressure PID during a test drive can give you insights into the health of the pump. If the pressure drops suddenly when accelerating, it could be a sign the pump is failing. The pressure should not change much during differing engine loads and speeds. This is because the pump is responsible for providing the correct volume while the pressure remains the same. Fuel pressure for most vehicles should stay in a 5-10 psi range. But, make sure you look at the service information for the specifications.

Other data PID used to regulate the fuel pump include the engine position sensors. Additional data used to control the pump could be the engine load and fuel requirements. The goal of these sensors is to provide the correct amount of fuel pressure at the fuel injector so when the fuel injector opens, it shoots an accurate amount of fuel into the cylinder with a proper spray pattern.

Sensing if there is a problem with the fuel pressure caused by a pump that is not producing the correct pressure and volume might be able to be seen in several data PIDs like fuel pressure and fuel trims. Drivability symptoms of a weak fuel pump might be a loss of power.

Some vehicles will record the fuel pressure as part of the freeze frame if a code is stored. This can help you track down an intermittent fuel pump problem.

Since the fuel pump module needs information for various sensors, it usually communicates on a serial data bus. If modules are not communicating, the fuel pump can’t be adequately controlled. The key to investigating these problems is to communicate with different modules to see what data PIDs are present and which ones are are missing.  iC

You May Also Like

AC Service – R1234yf

With a few simple steps, you can ensure that your A/C machine is properly maintained and ready for the upcoming A/C season!

Summer is just around the corner, and this is a perfect time to get your air conditioning machine serviced before the busy A/C season hits your garage bays. As the summer winds down and we move into the cooler months, most A/C machine usage winds down as well, with the machine sitting idle for longer periods of time, often unserviced at the end of the season. Now is the perfect time to get it ready to prevent any unwanted “downtime” from a machine that wasn’t serviced. Let’s look into what you can do to get your equipment ready.

Ignition Coil Output

To see inductance inside the primary windings, use an amp probe placed around the positive wire for the ignition coil.

Compressor Oil for R1234yf

Working on R-1234yf systems is not that different from the R-134a variety.

Turbochargers on Minis

No matter if it is a BMW or MINI, when the engine stops turning, the oil flowing to the turbocharger stops.

How Extended Interval Oil Filters Have Been Improved

Over time, the oil filter can collect enough contaminants to become restricted. Here’s why new filters are better.

Other Posts

AC Condensers

The characteristics that make the parallel-flow condenser so efficient are among its major drawbacks as well.

Lifter Deactivation

The area of contact between the lifters and cam lobes is the highest loaded surface inside an engine.

Mercedes-Benz AC Service

Here’s what you need to know about R-1234yf refrigerant in Mercedes-Benz vehicles.

Battery Charging and Diagnostics

Here are six tips to use when diagnosing a vehicle with a dead battery.