Tech Tips: Brake Lubricants - High Temperatures Require High Performance Products

Tech Tips: Brake Lubricants – High Temperatures Require High Performance Products

When it comes to brake lubricants, grease is a dirty word. Brake lubricants are specially-formulated products that are NOT the same as ordinary chassis grease or even multi-purpose grease.

When it comes to brake lubricants, grease is a dirty word. Brake lubricants are specially-formulated products that are not the same as ordinary chassis grease or even multi-purpose grease.

The kind of grease that’s used to lube tie rod ends, ball joints and U-joints is not the same as the lubricants that are required for brake system components. In fact, ordinary grease may cause serious problems if it is used on brake hardware or hydraulic components.One thing that makes the lubrication requirements for brake components different from that of steering and chassis components is heat. Brakes run hot. The front brakes on many front-wheel drive cars and minivans, as well as trucks and sport utility vehicles can easily reach several hundred degrees with normal braking, and get much, much hotter under certain circumstances.

Riding the brakes in heavy stop-and-go traffic, mountain driving, aggressive driving, towing a trailer, or hauling a heavier-than-normal load can all increase the load on the brakes and the operating temperature of critical brake components.

At elevated temperatures, most ordinary chassis grease can’t take the heat and will either melt or burn off, leaving surfaces unprotected and unlubricated. Worse yet, the grease may contaminate the brake linings if it melts and runs off the calipers or drum hardware. That’s why high temperature brake lubricant with a high solids content generally works best for brake system applications.

Another reason for not using ordinary chassis grease or multi-purpose grease on brake components is because these products are usually petroleum-based.

As every technicians should know, many petroleum-based products are not compatible with the seal materials that are commonly used inside brake systems. Petroleum-based grease or oil should never come into contact with the rubber seals, pistons or other internal parts in a master cylinder, brake caliper or wheel cylinder. If it does, the entire brake system should be considered contaminated. This will require draining and flushing the entire system, and replacing all the major hydraulic components! Why? Because petroleum-based products can cause incompatible seal materials to swell, rupture and leak — which could lead to fluid loss and brake failure.

Brake lubricants, by comparison, are specially formulated products that are designed exclusively for brake applications and nothing else. The chemicals in these products are compatible with all commonly used seal materials, and will not harm these parts.

SEVERAL BASIC TYPES
There are several basic types of brake lubricants: those that are designed for lubricating hardware and mechanical components and typically contain a high percentage of solids (dry film lubricants), and those that are designed for lubricating seals, boots and other internal parts when assembling calipers, wheel cylinders and master cylinders.

Brake lubricant for hardware is a special high temperature grease designed to provide long-lasting protection. The lubricant may be a synthetic or silicone-based product. Synthetic-based, boundary-type lubricants that come in a tube, paste or stick form have a high solids content and typically contain a variety of friction-reducing ingredients such as molybdenum disulfide (“moly” or MOS2) and graphite.

Moly and graphite are both dry-film lubricants that can handle high temperatures and pressures. Some of these products are rated to withstand intermittent temperatures as high as 2,400 degrees F!

Moly and graphite have excellent staying power and won’t evaporate or burn off over time, and they won’t attract or hold dirt like ordinary “wet” greases can. This type of product is ideal for high temperature applications where long-lasting metal-to-metal lubrication is essential for good brake performance.

Silicone-based brake grease is designed for caliper and wheel cylinder assembly work because silicone is an excellent lubricant for rubber and plastic. It is compatible with all rubber compounds including nitrile, teflon, nylon and other synthetic rubbers.

Silcone’s normal working range is -40 degrees F to 400 degrees F. But it does not have the high temperature staying power of a high solids synthetic lubricant, and it is a “wet” lubricant that can attract and hold dirt, making it less suited for lubricating external metal-to-metal contact points such as caliper mounts and shoe pads. This type of product is best suited for assembling calipers, wheel cylinders and master cylinders.

Another synthetic-based brake lubricant uses polyalphaolefin (PAO) as its main ingredient. PAO-based brake lubricants are also excellent for assembly work and lubricating seals and boots. PAO offers superior rust protection, making it well-suited for brake systems operated in wet environments.

PAO brake lubricant may also include various amounts of moly, graphite and teflon to enhance its lubricating properties. This type of product can withstand intermittent temperatures of up to 600 degrees F, and can be used for both assembly and external lubrication.

White lithium is a low-temperature grease that can be used to lubricate drum brake hardware and backing plates, but lacks the heat-resistance for front disc brake applications. So this type of grease is not the best choice for general brake work.Regardless of what type of brake lubricant you choose, always follow the supplier’s recommendations as to how their product should be used.

WHERE TO USE IT

Brake lubricant should be used at every point in the brake system where parts slide or move.

With disc brakes, lubrication points include the caliper slides, pins and bushings, the contact points where the pads slide within the caliper housing, self-adjuster mechanisms on rear disc brakes with locking calipers, and the parking brake cables and linkage.

Brake lubricant can also be used to dampen vibrations between disc brake pads and caliper pistons. But it should not be applied between the pads and any noise suppression shims that may be used. Use it on the back of a bare pad or between the pad shim and caliper — and use it sparingly. Don’t glob it on.

The primary lubrication points in rear drum brakes include the raised pads on the backing plates that support the shoes, the star adjuster mechanisms, hinge points for self-adjusters or the parking brake linkage, and the parking brake cables.

One place you never, ever want to get any grease on is the friction surface of a brake lining — which is another reason for not using low-temperature or petroleum-based lubricants which can melt, run off and foul the linings. Grease contaminated shoes or pads will be grabby and usually cause a brake pull to one side. The only cure is to replace the fouled linings with new ones. Cleaning is out of the question because solvents and cleaners can adversely affect the linings, too.

For lubricating hydraulic components, such as the piston seals inside calipers and wheel cylinders, you can use a silicone-based brake lubricant or ordinary brake fluid. This type of lubricant will help assure smooth movement of the seals in their bores, and will help prevent these parts from sticking or corroding.

You May Also Like

Shifting Your Focus To Find Satisfaction In Life

Monster Truck racer Bryce Kenny gives tips for shifting our mindsets to find purpose in life and being more fulfilled.

When the workday is over, the tools are put away, the computers have gone to sleep, the customers have driven away safely and the last tech has clocked out, washed up and left the parking lot, do you ever just take a minute to put your hands on your hips, look around your shop, take a deep breath and think, “Is this really all there is to life?”If so, you’re probably not alone.

Confusion, Carcasses and Catalytic Converters

Dealing with warranty return headaches starts with fixing the real problem that caused the failure to begin with.

Euro Clinic Wins 2023 Women in Auto Care Automotive Communications Award for Best Website

The family and female-owned auto repair shop provides high-quality repair services for European vehicles to the Santa Clara, California areas.

DeWalt Launches Line of Residential Level 2 EV Chargers

DeWalt launched a new line of residential Level 2 EV chargers, responding to the increasing demand for efficient home charging solutions.

Chassis Alignment

The source of the complaint can be the angles, electronics or tires.

Other Posts

Quality Triumphs!

If a brand of parts has a great reputation and hasn’t caused a comeback, stick with that brand.

Autel’s TS900 TPMS Tool

Beyond TPMS, the Autel TS900 shines as a full-service and maintenance tool. Sponsored by Autel.

Mazda Front Radar Calibration

Joe Keene discusses how to calibrate the front radar on a Mazda — the key to which is precisely establishing the centerline.

SAE Selects MAHLE for EV Charging Standard

MAHLE’s system employs a magnetic field to connect the EV to a controlled charging point as it approaches.