Tech Tip: Servicing Clutch Slave Cylinders

Tech Tip: Servicing Clutch Slave Cylinders

Clutch slave cylinders located inside the bell housing require special handling to guarantee proper operation. Some designs feature plastic straps to hold the hydraulic piston in place during installation. Don’t remove them; they break free when the clutch pedal is actuated.

Internal (Concentric) Slave Cylinders
Clutch slave cylinders located inside the bell housing require special handling to guarantee proper operation. Some designs feature plastic straps to hold the hydraulic piston in place during installation. Don’t remove them; they break free when the clutch pedal is actuated.

Never change the position of the release bearing, you may damage the seal and void the warranty. Never drop the slave unit or bend the hydraulic lines. Inspect the new unit for damage before installation, including the protective grommets. Grommets isolate destructive vibrations and must be installed properly.

Never grease the slave or clean it with solvents.

Always use the installation hardware included with the unit and avoid over-tightening, which may crack the housing.

Use only fresh, manufacturer-recommended brake fluid.

Special considerations: Some Jeep applications require you to remove the “quick disconnect” fittings from the hydraulic lines.

Proper Bleeding Procedures for Slave Cylinders Without Bleed Screws
Some slave cylinder designs do not include a bleed screw to purge air. The unit may have a gold Allen screw, which is not for bleeding; do not remove or loosen it. Follow this procedure for proper bleeding.

1. Push the slave cylinder pushrod inward and disconnect both bands of the retaining strap, allowing the pushrod to fully extend. Never cut or discard the retaining strap.

2. Tilt the slave cylinder at a 45-degree angle with the master cylinder line port facing upward and the port at the high end of the slave. Fill the slave cylinder with fresh, clean brake fluid.

3. Insert the master cylinder line into the slave cylinder port. Lubricate the enclosed O-ring with brake fluid and insert the retaining pin.

4. Hold the slave cylinder vertically with the pushrod facing down, so that the slave cylinder is lower than the master cylinder. If this is not possible, position the slave as far vertically as possible without putting excessive load on the master cylinder line.

5. Remove the master cylinder reservoir cap and slowly push the slave cylinder pushrod inward approximately 1", watching for air bubbles in the master cylinder reservoir. Stroke the pushrod 10 to 15 times to fully purge the air in the release system.

6. When the air is fully purged, slowly push the slave cylinder pushrod back into the slave and reconnect the two bands of the retaining strap.

7. Install the slave cylinder with the retaining strap in place. The strap will break free with the first stroke of the pedal.

Note: Do not remove the plastic cover on the end of the pushrod or the clutch will not release properly.

Courtesy of LuK Automotive Systems, 5370 Wegman Drive, Valley City, OH 44280. Phone: 800-274-5001. Fax: 330-273-3522. Website: www.lukclutch.com.

You May Also Like

Solving VW False Fuel Pressure Reading

First, verify the customer did not run out of fuel at the time the DTCs were stored.

vw steering wheel squeak

MIL ON with DTCs P310B, P129F, P008B, P129E, P008A, P2540 or P0087 Stored in ECM Fault Memory

2007-2008 Eos (2.0L - BPY)

2007-2008 Jetta (2.0L - BPY)

2007-2008 GTI (2.0L - BPY)

Tech Tips for Dorman’s OE FIX Steering Tie Rod End Assembly

Read the tech note for tips on installation of this unique fix.

Acura Frozen Starter Causes No Start

Why won’t the engine crank after the vehicle has been exposed to precipitation and then freezing temperatures?

Strut Sales

It all comes down to educating the customer about the benefits and asking for the sale.

Beating the Tech Shortage Through Mentoring

How understanding the 80/20 Rule and creative mentoring can make the shortage less threatening.

Other Posts

Nissan Key Will Not Start

Nissan keys use radio frequencies (RF) similar to other everyday wireless devices.

Taking the Fear out of ASE Testing

Spring registration now open; Register by June 30.

Audi EVAP Case Study

Let’s look at some of the things that you should know about Audi EVAP systems before trying to tackle such a repair.

Exhaust Gas Recirculation Operation and Diagnosis

Since exhaust gas does not burn, this lowers the combustion temperatures and reduces NOx emissions from the engine.