Tech Tip: Servicing 1998-1999 Passats Experiencing Delayed Shifts During Cold Start Warm-Up

Tech Tip: Servicing 1998-1999 Passats Experiencing Delayed Shifts During Cold Start Warm-Up

Some 1998-’99 Passat 2.8L models with 01V transmissions may exhibit delayed upshifts under partial load after a cold start.

Some 1998-’99 Passat 2.8L models with 01V transmissions may exhibit delayed upshifts under partial load after a cold start. A warm-up program determines this shift characteristic and is activated when the following conditions apply:
– Fresh start of engine; and
– Coolant temperature below 40 C (104 F).

Note: The warm-up program lasts for approximately 40 seconds after shifting into drive and the vehicle is moving under the above conditions.

During this period, the program holds the shift points to approximately 3,000 rpm (shifting at this rpm may be observed by the driver as harsh).

This condition is normal. No repairs are necessary, but explain the technical facts to customers inquiring about the different shift points.

By raising the shift points, the emission warm-up phase is reduced and the catalyst is heated faster for improved efficiency and better emissions performance.

To verify activation of the warm-up program, use the following procedure.

SERVICE PROCEDURE:
1. Connect the VAG 1551 scan tool.
2. Start the engine.
3. Ensure the coolant temperature is below 40 C (104 F).
Note: The verification process must be completed within the first 40 seconds after vehicle is driven and the water temperature is below 40 C (104 F).
4. Start the vehicle.
5. Press buttons 0 and 2 to enter the address word 02 “Transmission electronics.”
6. Press buttons 0 and 8 to select "Read measured value block" function 08.
7. Confirm the entry with the "Q" button.
8. Enter display group number 002.
9. Confirm the entry with the "Q" button.
10. Four display fields always appear in the measured value block (in physical values if necessary).
11. Apply the brake pedal.
12. Shift the vehicle into drive.
13. Drive the vehicle away while a second technician observes the value in display field 1 "Dynamic shift program index."
14. A value of 241 will be displayed in field 1.
15. After 40 seconds, or if coolant temperature exceeds 40 C (104 F), the value will change from 241 to a lower value.
Note: When placed in park, the value will return to 241.
16. The verification process is complete.

Technical service bulletin courtesy of ALLDATA.

You May Also Like

Solving VW False Fuel Pressure Reading

First, verify the customer did not run out of fuel at the time the DTCs were stored.

vw steering wheel squeak

MIL ON with DTCs P310B, P129F, P008B, P129E, P008A, P2540 or P0087 Stored in ECM Fault Memory

2007-2008 Eos (2.0L - BPY)

2007-2008 Jetta (2.0L - BPY)

2007-2008 GTI (2.0L - BPY)

Tech Tips for Dorman’s OE FIX Steering Tie Rod End Assembly

Read the tech note for tips on installation of this unique fix.

Acura Frozen Starter Causes No Start

Why won’t the engine crank after the vehicle has been exposed to precipitation and then freezing temperatures?

Strut Sales

It all comes down to educating the customer about the benefits and asking for the sale.

Beating the Tech Shortage Through Mentoring

How understanding the 80/20 Rule and creative mentoring can make the shortage less threatening.

Other Posts

Nissan Key Will Not Start

Nissan keys use radio frequencies (RF) similar to other everyday wireless devices.

Taking the Fear out of ASE Testing

Spring registration now open; Register by June 30.

Audi EVAP Case Study

Let’s look at some of the things that you should know about Audi EVAP systems before trying to tackle such a repair.

Exhaust Gas Recirculation Operation and Diagnosis

Since exhaust gas does not burn, this lowers the combustion temperatures and reduces NOx emissions from the engine.