Tech Tip: Basic Cylinder Head Gasket Installation Tips

Tech Tip: Basic Cylinder Head Gasket Installation Tips

For a successful repair, the cylinder head gasket must seal fuel, air, vacuum, hot pressurized combustion gases, coolant, as well as high and low pressure oil. The following tips will help ensure that a quality repair is made.

For a successful repair, the cylinder head gasket must seal fuel, air, vacuum, hot pressurized combustion gases, coolant, as well as high and low pressure oil. The following tips will help ensure that a quality repair is made.

1. Make sure the reason for head gasket failure is properly diagnosed – rarely does a head gasket fail on its own accord.

A. Consider the driving conditions the engine is being placed under – many times engine damage or gasket failure is the result of asking too much of a drivetrain.
B. Make sure overheating engines are properly repaired.
C. Make sure all induction symptoms are working properly – detonation and pre-ignition will cause pre-mature gasket failure.

2. Make sure the head and block are in best condition possible – the smoother and flatter the better!

A. Make sure both block and head are within published flatness specification for the specific engine being repaired.
B. Make sure castings are thoroughly checked for cracks, pitting and scratches.
C. Make sure the head and block surfaces are as smooth as possible – make sure your machine shop knows what finish they are producing.
D. Never use abrasive disks on the head or block – these can lead to damaged or uneven mating surfaces that can cause internal or external leaks; always use a solvent and a soft scraper (rubber or plastic).
E. Handle newly machined parts with care – many times castings are scratched or damaged by careless handling after an expensive, high-quality finish is achieved.
F. Make sure mating surfaces are clean – all dirt and debris must be removed (use of RTV and other chemicals on head gaskets is not recommended for too many reasons to list).

3. Make sure proper bolt load is achieved – friction is the enemy.

A. Always use new torque-to-yield head bolts – stretched bolts do not return to original specifications and can yield very erratic results.
B. Always clean old bolts with solvent and a soft bristled brush – do not tumble or wire wheel as damage to the threads can easily occur.
C. Bottom tap all holes in the block, making sure that threads are in the best possible condition.
D. Use light engine oil on bolt threads and under the bolt head – do not dip bolts in oil as hydraulic lock can occur in blind holes resulting in possible casting damage.
E. Always consult and follow the latest OEM torque specification – never guess as each engine is unique and many late-model applications torque specifications often change.
F. Periodically have your torque wrench calibrated – all precision shop gauges need to be periodically serviced to maintain their accuracy.

For additional information on cylinder head gaskets, visit Corteco’s website at www.corteco-na.com.

You May Also Like

Solving VW False Fuel Pressure Reading

First, verify the customer did not run out of fuel at the time the DTCs were stored.

vw steering wheel squeak

MIL ON with DTCs P310B, P129F, P008B, P129E, P008A, P2540 or P0087 Stored in ECM Fault Memory

2007-2008 Eos (2.0L - BPY)

2007-2008 Jetta (2.0L - BPY)

2007-2008 GTI (2.0L - BPY)

Tech Tips for Dorman’s OE FIX Steering Tie Rod End Assembly

Read the tech note for tips on installation of this unique fix.

Acura Frozen Starter Causes No Start

Why won’t the engine crank after the vehicle has been exposed to precipitation and then freezing temperatures?

Strut Sales

It all comes down to educating the customer about the benefits and asking for the sale.

Beating the Tech Shortage Through Mentoring

How understanding the 80/20 Rule and creative mentoring can make the shortage less threatening.

Other Posts

Nissan Key Will Not Start

Nissan keys use radio frequencies (RF) similar to other everyday wireless devices.

Taking the Fear out of ASE Testing

Spring registration now open; Register by June 30.

Audi EVAP Case Study

Let’s look at some of the things that you should know about Audi EVAP systems before trying to tackle such a repair.

Exhaust Gas Recirculation Operation and Diagnosis

Since exhaust gas does not burn, this lowers the combustion temperatures and reduces NOx emissions from the engine.