Tech Feature: Eliminating the Con-'Fusion' of Servicing Ford's Mid-Size Vehicles

Tech Feature: Eliminating the Con-‘Fusion’ of Servicing Ford’s Mid-Size Vehicles

Nestled into the marketing space between the Focus and the Taurus/Five Hundred is the Ford Fusion. The Fusion came with a choice of four-cylinder and six-cylinder Duratec powerplants. The inline four-cylinder Duratec 23 is a 2.3L 16-valve DOHC engine.

Nestled into the marketing space between the Focus and the Taurus/Five Hundred is the Ford Fusion. The Fusion came on the scene in 2006, and shared a design platform with the Mercury Milan and the Lincoln Zephyr. However, in 2007, the Zephyr was replaced by the Lincoln MKZ.

Internal Issues
The Fusion came with a choice of four-cylinder and six-cylinder Duratec powerplants.

The inline four-cylinder Duratec 23 is a 2.3L 16-valve DOHC engine.

It uses a 9.7:1 compression ratio and produces 160 hp at 6,500 rpm and 150 ft.-lbs. of torque at 4,000 rpm.

The head and block are both aluminum. It is a coil-on-plug ignition and uses electronic throttle control.

fusion 2.3l engineIt is a Partial Zero Emissions Vehicle (PZEV) certified engine and has a 150,000-mile recommended tune-up.

To enhance efficiency, the Duratec 23 features Charge Motion Control Valves in the intake runners — similar to those found in the powerful F-150 pickup — to boost torque and improve combustion at low engine speeds. To reduce vibration, the inline four cylinder employs hydromounts in two positions — at the engine and the roll restrictor.

Did You Know…
The I-4 features a direct-acting mechanical bucket-tappet valvetrain, while the V6 engine features a hydraulically lash-adjusted roller-finger follower valvetrain.

In the 2006 model year, the V6 choice is limited to a 3.0L 24-valve DOHC Duratec 30 engine, which uses a 10:1 ratio and also was built for 87 octane. It produces 221 hp at 6,250 rpm and 205 ft.-lbs. of torque at 4,800 rpm.

The Duratec 30 has hydraulic mounts to isolate engine vibration and movement from the vehicle’s chassis and to level out gearshifts. Hydromounts are filled with a viscous fluid that is pumped from one internal chamber to another in response to the powertrain’s movement. fusion 3.0l v6 engine

To further refine engine character and improve durability, both engines feature deep-skirted engine blocks. The Duratec 30 also uses a front engine cover made of a sheet metal “sandwich” to absorb sound through what is known as constrained layer damping.

The MKZ version sports a 3.5L 24 DOHC engine using a timing-chain-driven water pump. This engine uses a 10.3:1 compression ratio and still uses 87 octane fuel. The 3.5L engine produces 263 hp at 5,950 rpm and 249 ft.-lbs. of torque at 4,500 rpm. All three engines feature chain-driven cams and intake phase shifting (IPS) cam timing that can vary up to 29°.

With IPS on a Ford, as duty cycle command from the PCM increases, the cam timing retards. This concept is backwards from that of what you’d find on a Ford vehicle, like a 5.4L, that uses DEPS (Dual Equal Phase Shifting). Unlike EPS (Exhaust Phase Shifting) found on the 2.0L DOHC Focus/Contour/ Escort engine, DEPS and IPS will still use an EGR valve.

Did You Know…
There is no serviceable fuel filter on these vehicles. The fuel filter is built into the fuel pump. But, at least they gave us a trap door under the rear seat to access the fuel pump for replacement.

 

Transmission Service

The transmission choices in the Fusion/Milan/Zephyr/MKZ are the G5M 5-speed manual and FNR5 5-speed auto for the 2.3L versions. The manual transmission has no fluid surprises. It uses 75w90 gear oil.

However, the 5-speed automatic does have a surprise — it doesn’t use Mercon V. The fluid requirement of the 5-speed auto is Mazda V trans fluid. Do not confuse Mazda V fluid for Mercon V, it is not the same thing. The Motorcraft part number for Mazda V fluid is XT-9-QMM5. The 3.0L and the 3.5L have Aisin 6-speed automatics.

The 6-speed auto also contains a fluid requirement surprise of its own. It does not use Mercon V or Mazda V. It simply uses a Mercron/Dextron equivalent.

Also, when looking at the side of a 6-speed trans in a Fusion/ Milan/Zephyr/MKZ, you’ll notice that there are quite a few wires going into the transmission range sensor. That is because it is not just a range sensor, it is also the transmission control module.

So, if you get one of these with a faulty range sensor, you won’t be able to replace it unless your shop can program modules.

map sensor

Fluids and Lubes
All of the Fusion engines use 5w20 engine oil. The 2.3L has a service-able filter for the VCT solenoid. The filter is accessed from under the valve cover.

At the intake cam thrust cap is a plug with an allen socket head. Remove the plug and the filter is under it. The base part number on the filter is 6C683. There is no specified mileage for replacement.
On all-wheel-drive models, the Power Transfer Unit (PTU) does not fill all the way to the filler hole like a typical transfer case would. Instead, the fill mark is 1-1/2” below the fill hole. To check the level, you must fabricate a dipstick from a plastic tie strap.

Mark the tie strap 1-1/2” from the tapered end with a marker, then again at 1-1/2” from the end. Bend the tie strap into a right angle so that the tip points down when inside the fill hole. Lower the strap in until the upper mark is at the bottom edge of the filler hole. Remove and see where the strap is wet. It should be at the first line.

egr valve If it is low with no external signs of leakage, then the left internal axle seal is probably leaking. There is a cavity inside the case between the inner and outer axle seal that can fill with fluid. If the PTU is over-filled, then it will push fluid out of the vent at the top when driving.

Note: There is no drain plug on the PTU so draining an over-filled PTU will be difficult. The PTU requires 75w140 synthetic gear oil.

The Rear Drive Unit (RDU) of an AWD Fusion is similar to the RDU of an AWD Escape except that they have different gear ratios. So, even though they might appear outwardly that they will interchange, they will not.

EGR, MAP and Other Sensors
Both the four-cylinder and V6 ­engines use a stepper motor EGR valve. The MAP sensor on these vehicles is used to infer EGR flow, not fuel control.

These engines also use electrically heated PCV valves. The heater in the valve is to prevent icing in the PCV and on the back of the throttle plate. The PCV heater circuits are monitored by the PCM and will set an MIL illuminating code if there is a circuit-related fault present.


Did You Know…
The Fusion radio is a programmable module, meaning if it is replaced for a new one, the new one will have to be programmed with a scan tool or the back lighting will not work.

cam-driven water pump
Adjusting Your Belt
There is no adjustable power steering tensioner on the 3.5L. The 3.5L uses what is called a “stretch belt.” This belt is slightly elastic by design. It is removed and installed by rolling it off and rolling it on. This belt cannot tolerate lubricants, so do not spray these belts with any kind of ­lubricant or dressing.

If something leaks onto this belt, it must be ­replaced. Ford has tools 303-1252/2 to aid installation and 303-1252/1 to aid in removal.

Note: The V6 uses a cam-driven water pump at the rear of the left cylinder head.

Marker Lights Trick
Located in the forward side of the front inner fender is an access panel through which you can replace the exterior marker light bulbs.

Cool Down
When servicing the A/C system on these vehicles there are a couple of things to note about the condenser. The top two rows in the condenser are the power steering cooler. This similar idea is also used in the newer Escapes, however, in the ­Escape, these upper rows are the transmission cooler.

Fusion condenser The condenser on the Fusion also houses an integrated receiver/drier. The drier is a molded housing down one side of the condenser. Inside of the drier housing is a serviceable desiccant filter. To replace the desiccant filter, remove the snap ring at the top of the assembly, remove the aluminum plug and slide the filter out.

These vehicles are optional with heated and cooled seats. The seat cooling is achieved by use of a Thermal Electric Devise (TED).

This is not just simply piping A/C vent air into the seats. Instead, a TED is a series of semi-conductors that can absorb and transfer heat. Inside the seat are a fan, tubing and a TED.

The TED has a filter under the seat that is to be replaced every three years or 36,000 miles. To replace the seat filter, adjust the seat all the way back, push up on the plastic out-ring of the filter and rotate until it unlocks.

Reverse to install.

You May Also Like

ASE Education Foundation, Goodguys Continue Partnership

Goodguys is one of many industry relationships the foundation has developed to help solve the technician shortage.

The ASE Education Foundation and Goodguys Rod and Custom Association (Goodguys) are continuing their partnership and will conduct educational awareness seminars at select Goodguys events throughout the 2024 season.

Since its inception, the ASE Education Foundation has brought industry and education together to develop entry-level technicians. Goodguys is one of many industry relationships the Foundation has developed to help solve the technician shortage.

BMW Diagnostics: Low Airflow After Cabin Filter Replacement

Models:  F97 X3 M  F98 X4 M G01 X3 G02 X4 G20 3-Series SITUATION After replacing the microfilter during a previous service, the customer notices that the ventilation system airflow rate is noticeably less. This leads to perceived lower cooling power. The customer may also notice that external odors enter the vehicle. Related Articles –

Volvo Modular Engine Service

The Volvo Modular Series engine outlasted Ford and was retired by Geely. The Volvo modular design that can have four, five or six cylinders made its debut in 1990 in the 960 sedan as a six-cylinder and never stopped improving. Related Articles – How To Service BMW Tire Monitor Systems – VW DSG Maintenance –

BMW Cooling System Problems

Let’s take a closer look at this unique water pump, how to replace it efficiently and what other components should be replaced along with it.

Audi Active Suspension Service

The key to servicing these systems is proper information and understanding precisely how these systems operate.

Other Posts

Now Available – March’s Digital Edition of ShopOwner

The March issue includes technical and management content and is free to download.

Chassis Diagnostic Procedures

The secret is to be quiet & listen, as the customer will tell you almost everything relevant to the repair you need to know.

Today’s Fuel Pressure Diagnostics

Direct injection pressure is measured with sensors, and the signals are used to determine pump speed and/or volume.

Valvoline Celebrates Female Service Center Employees

As women make up more than half of all drivers in the United States, Valvoline is taking steps to increase their vehicle care confidence.