Servicing R1234yf: Are You Ready?

Servicing R1234yf: Are You Ready?

R1234yf, tabbed the replacement for R134a, has been in service now for a few years on certain models from FCA and GM as well as several European models. R1234yf is estimated to be fitted on 35 million vehicles worldwide. The EU has already banned R134a as of Jan. 2017, and the U.S. will follow suit by 2020. While most independent shops haven’t had to deal with it yet, you will start seeing them soon, so you should be prepared to service them by getting the right tools.


“Air conditioning systems are going through an unprecedented transformation,” says ASE President Timothy Zilke. “What was once a simple creature comfort for upscale motorists, air conditioning systems of today are true thermal management systems, providing not only occupant comfort, but also providing essential cooling to battery packs and onboard computers in hybrid vehicles.”

R1234yf, tabbed the replacement for R134a, has been in service now for a few years on certain models from FCA and GM as well as several European models. R1234yf is estimated to be fitted on 35 million vehicles worldwide. The EU has already banned R134a as of Jan. 2017, and the U.S. will follow suit by 2020. While most independent shops haven’t had to deal with it yet, you will start seeing them soon, so you should be prepared to service them by getting the right tools.

Although some equipment is rated as compatible with both R134a and R1234yf, you will still need a machine that is specific for R1234yf to recover and recycle the new refrigerant. You will also need to understand the new oil compatibility issues with the R1234yf and what happens when refrigerants mix. If your shop doesn’t already have one, you should invest in a refrigerant identifier tool.

With new technology comes new tools and equipment, and R-1234yf is no different. SAE has set the standards for equipment used to service R1234yf systems. R-134a service equipment and system components are not interchangeable with R1234yf systems unless they meet the relevant SAE standards. These systems have a different service port design to those designed for R134a to prevent cross-contamination.


According to the EPA, it’s illegal to put R-134a or any other refrigerant into a car originally equipped with R-1234yf. It could be considered “emissions tampering” if the manufacturer counts air conditioning credits (use of R-1234yf) toward light-duty, greenhouse gas (LD GHG) compliance. Many R-1234yf systems also use an internal heat exchanger (IHX) not commonly found on R-134a vehicles. The IHX is integral to the low-side system plumbing and improves cooling efficiency. Of course, like other A/C systems, R-1234yf systems will have a unique system label showing the refrigerant type, charge amount, oil type and more.

Most vehicle air conditioning systems have two service ports for “high” and “low” pressure, but some may have only one. This is also the case with vehicles using HFO-1234yf, except the difference will be the service ports are different in size, shape and thread pattern. The service ports for R1234yf still use the protective external caps, but the caps are new and use the new diameter and threads. Your service and test equipment and the refrigerant tanks must have the correct connectors to match and connect to the new ports. Shops will need to purchase new manifold gauges, recovery machines, etc., to service these systems.

Before any work is done, you must identify the refrigerant using the correct identifier tool. Refrigerants must be separated to prevent contamination in not only the vehicle, but also in your shop equipment. Mixing refrigerants can cause improper system pressures, component damage, diagnostic errors, and hazards to people and the environment.


Check the refrigerant label to learn what should be in the system. Then, connect the identifier to determine what is in the system. A vehicle may have been repaired with incorrect or impure refrigerant during a previous repair. The tool can also check what is in a tank of refrigerant. SAE J2843 requires that all recovery/recycle/recharge machines built for use with HFO-1234yf have either an integrated refrigerant identifier that complies with SAE J2927, or shall be capable of receiving input from a non-integrated, SAE J2912 compliant identifier via an integrated USB port. After you identify the refrigerant, the tool will report the results. Some tools give only a Pass-Fail notification, while others will report the percentages of refrigerant. R1234yf systems use quite a bit less refrigerant than older R-134a systems and are less tolerant of incorrect amounts.

With lower system charge amounts for R1234yf, better system integrity and virtually no leakage, the amount of refrigerant needed won’t be the same as in the past. This could mean that refrigerant “top-offs” are a thing of the past, as well.

You May Also Like

Belt Service For Hybrid and Stop/Start Systems

Knowing how to “force start” a hybrid vehicle can be helpful if you are trying to diagnose a noise problem that involves the accessory belt drive system.

Here is a tech tip you can use if you are seeing more hybrids and stop/start vehicles with noise complaints at your shop. Noise problems can be challenging to replicate on these vehicles because the gasoline engine doesn’t run constantly and starts only under specific conditions.

Key Programming

When it comes to key programming, there are different levels of security access depending on the year, make and model of the vehicle.

ECU Reflashing

Reflash procedures are not getting any faster.

The Impact of Fuel Type on Engine Performance

When recommending fuel options for customers, consider engine design, manufacturer recommendations and usage.

Battery Management Means Knowing How It Ages

The battery may be fully charged, but you also need to measure how low the voltages go while the engine is cranking.

Other Posts
Motor Mount Technology and Failures

Engines have noticeably changed in the past decade. Fewer cylinders, more power at lower RPM and more detectable vibration at idle are just a few of the differences in today’s engines. Related Articles – Audi Tech Tip: Key Can’t Be Removed From The Ignition – Mercedes-Benz Clunking Noises – Tech Tip To Quiet Customers –

AC Service – R1234yf

With a few simple steps, you can ensure that your A/C machine is properly maintained and ready for the upcoming A/C season!

Ignition Coil Output

To see inductance inside the primary windings, use an amp probe placed around the positive wire for the ignition coil.

Compressor Oil for R1234yf

Working on R-1234yf systems is not that different from the R-134a variety.