Performing A Brake Job On A 2007-2013 Toyota Tundra

Performing A Brake Job On A 2007-2013 Toyota Tundra

For 2007, the Toyota Tundra was redesigned. The body changed, and the foundation brake system was also updated with larger front brake calipers and rear disc brakes. The control system and hydraulics changed with a new vehicle stability system that included yaw, steering angle and brake pedal load sensors.

For 2007, the Toyota Tundra was redesigned. The body changed, and the foundation brake system was also updated with larger front brake calipers and rear disc brakes. The control system and hydraulics changed with a new vehicle stability system that included yaw, steering angle and brake pedal load sensors. 
 
Overall, this is one of the easier brake jobs. Changing the front brake pads does not require the application of lubricants. The rear brakes are a lot easier to service when compared to the previous models. 
Front Brakes
The front brakes use the typical Toyota truck four-piston caliper. The pads are held in with pins that have an anti-rattle clip on the lower pin and a pin holder clip. These items should not be reused when replacing the pads. A quality pad set will include these in the box.

Toyota has designated the bolts that hold the caliper to the knuckle as non-reusable parts. Replacement bolts are readily available. Some remanufactured calipers include new bolts.
 
When removing the pads or pushing back the pistons, use the correct tool. A brake pad spreader can not only save time, but also prevent damage to the piston boots. 
 
The OE friction formulation on the Tundra is ceramic. A replacement brake pad should be of a similar formulation. 
 
The original pads on the Tundra come with shims. Do not lubricate the back of the pad with any lubricant. The lubricant will only transfer onto the piston boots and cause them to attract debris. This can lead to an early failure. 
 
Pulsation is an issue with some 2007-2009 Tundra models. Most of the issues are related to excessive runout or uneven deposits of friction material on the rotor. The runout specification on the Tundra is .05 mm or .002”. The hub flange should have almost zero runout. 

Rear Brakes
The 2007 Tundra is equipped with disc rear brakes with the parking brake in the hub. The caliper is a floating design with a single piston. The OE friction formulation is ceramic. The OE backing plate uses a clip-style shim. 
 
According to Toyota, the abutment clips and guide pin boots are non-reusable parts that should be replaced if the pads are serviced. The guide pins should be lubricated with a brake-specific lubricant that is not petroleum based. 
Parking Brake
To adjust the parking brake, insert an adjustment tool into the adjustment hole on the disc. 
1. Rotate the adjustment wheel in the "X" direction until the shoes are locked. 
2. Rotate the adjustment wheel in the "Y" direction 8 notches.
3. Check that the disc can be rotated smoothly. If not, rotate the adjustment wheel in the "Y" direction and check again.
4. Install the hole plug.

You May Also Like

Toyota Prius Battery Codes P0A7F, P2011 and P0A80

A second generation Toyota Prius is at least 12 years old and batteries may need to be replaced. Here’s what the codes mean.

Battery pack replacement is becoming more common as hybrid vehicles age. The second-generation Prius started with the 2004 model year and lasted until 2009. They have racked up many miles in the past decade or more, and the nickel-metal hydride battery is probably not providing the same range as before.

Air Ride Diagnostics: Reservoirs and Compressors

The secret to diagnosing air ride problems is knowing what criteria the system uses to regulate the compressor/reservoir and having the right tool.

Mazda SkyActiv Engine Service Tips

These engines have been reliable, but there are four pattern failures you might see.

Honda Indirect TPMS Systems

Honda indirect TPMS systems do not have air pressure sensors inside the tires.

Honda Oil System Inspection

The leading cause of low oil pressure-related complaints with Honda vehicles is the oil level.

Other Posts

ASE Education Foundation, Goodguys Continue Partnership

Goodguys is one of many industry relationships the foundation has developed to help solve the technician shortage.

Valvoline Celebrates Female Service Center Employees

As women make up more than half of all drivers in the United States, Valvoline is taking steps to increase their vehicle care confidence.

BMW Diagnostics: Low Airflow After Cabin Filter Replacement

Models:  F97 X3 M  F98 X4 M G01 X3 G02 X4 G20 3-Series SITUATION After replacing the microfilter during a previous service, the customer notices that the ventilation system airflow rate is noticeably less. This leads to perceived lower cooling power. The customer may also notice that external odors enter the vehicle. Related Articles –

BorgWarner Announces Plan to Reduce Supply Chain Emissions

A partnership with Manufacture 2030 will support BorgWarner in reaching its Scope 3 emissions reduction goal.