Honda Pilot Suspension And Alignment Inspection

Honda Pilot Suspension And Alignment Inspection

The Pilot employs a strut-type front suspension that provides a generous 7.3 inches of wheel travel. Separate load paths to the unit body are provided for the coil spring and the shock absorber to reduce road noise. A solid 0.9-inch stabilizer bar is linked directly to the strut via ball-joint connections to reduce body roll during cornering maneuvers.

u can charge the customer for this procedure. The Honda warranty time is around .3 hours.

TECH TIP: Noise/Judder from Rear of Vehicle
If a customer with a 2003 and later Pilot or 2006 and later Ridgeline complains of a noise and judder from the rear of the vehicle when turning, the VTM-4 differential fluid could likely be contaminated by clutch wear, condensation or both. This causes the VTM-4 differential clutches to make noise and to judder when turning.

Note: Worn VTM-4 fluid that has not been replaced at the recommended service intervals can cause the same condition. Check to see if the VTM-4 fluid has been replaced at the recommended intervals.

Corrective Action:
Replace the VTM-4 differential fluid.

Parts Information:
• Drain Plug Washer (18 mm, drain plug sealing washer), P/N 90471-PX4-000; and
• Drain Plug Washer (20 mm, filler plug sealing washer), P/N 94109-20000.

Required Materials:
• VTM-4 Differential Fluid (5.6 quarts required), P/N 08200-9003.

Diagnosis:

Do 10 figure-eight patterns with the steering wheel at full lock. Listen for a noise and feel for a judder. Accelerate at the start of each circle to make sure the clutches engage and disengage. Do not use the VTM-4 LOCK button.
Note: As an alternative to doing figure-eight patterns, you may do 10 circles to the left and 10 circles to the right.
• If you can hear the noise or feel the judder, go to the Repair Procedure.
• If you cannot hear the noise and feel the judder, continue with normal troubleshooting.

Repair Procedure:

1. With the engine off, raise the vehicle on a lift in a level position.

2. Remove the differential filler plug and its sealing washer. Save the sealing washer.

3. Remove the differential drain plug and its sealing washer to drain the VTM-4 differential fluid. Save the sealing washer.
Note: The drained fluid should look red. If it looks pink, it means water entered the VTM-4 differential through the vent tube breather in the rear subframe. This can happen after launching a boat or driving through water deep enough to cover the tires. If the fluid looks pink, replacing the fluid may not get rid of the noise and judder.

4. Clean the drain plug, then reinstall it with the sealing washer you saved in step 3. Torque the drain plug to 47 Nm (35 lb.-ft.).

5. Fill the differential with VTM-4 differential fluid until the fluid level reaches the bottom of the filler hole.
Note: To avoid contamination, always fill from an unopened VTM-4 fluid container. Always use a dedicated hand-operated fluid pump to fill the differential. Use fluid pump P/N 07AAK-PGJA220 or a commercially available fluid pump. Never use a pump driven by compressed air.

6. Reinstall the filler plug with the sealing washer you saved in step 2. Torque the filler plug to 47 Nm (35 lb.-ft.).

7. Drive the vehicle in a figure-eight pattern with the steering wheel at full lock. Accelerate at the start of each circle to ensure the clutches engage and disengage. Complete at least 10 patterns.

8. With the engine off, raise the vehicle on a lift in a level position.

9. Remove the oil filler plug and its sealing washer. Discard the sealing washer.

10. Remove the drain plug and its sealing washer to drain the VTM-4 differential fluid. Discard the sealing washer.

11. Clean the drain plug, then reinstall it with a new 18 mm sealing washer. Torque the drain plug to 47 Nm (35 lb.-ft.).

12. Fill the differential with VTM-4 differential fluid until the fluid level reaches the bottom of the filler hole.

13. Reinstall the filler plug with a new 20 mm sealing washer. Torque the filler plug to 47 Nm (35 lb.-ft.).

14. Test drive the vehicle in a figure-eight pattern to make sure the noise and judder are gone. Accelerate at the start of each circle to ensure the clutches ­engage and disengage.
Note: You may need to do up to 10 patterns to get rid of the noise and judder. 

You May Also Like

ADAS Calibration Tips

Here are 10 tips to follow during ADAS Calibration.

Millimeters Matter

When you set up a target or fixture for a camera or radar, the position and distance from the vehicle are critical to the performance and operation of the system. If the target or fixture is a few millimeters off when placed a few meters from the sensor, it can change the alignment of the sensor by meters when it is pointed down the road or the vehicle’s height is in the blind spot

Air Ride Diagnostics: Reservoirs and Compressors

The secret to diagnosing air ride problems is knowing what criteria the system uses to regulate the compressor/reservoir and having the right tool.

Mazda SkyActiv Engine Service Tips

These engines have been reliable, but there are four pattern failures you might see.

Honda Indirect TPMS Systems

Honda indirect TPMS systems do not have air pressure sensors inside the tires.

Honda Oil System Inspection

The leading cause of low oil pressure-related complaints with Honda vehicles is the oil level.

Other Posts

Now Available – March’s Digital Edition of ShopOwner

The March issue includes technical and management content and is free to download.

ASE Education Foundation, Goodguys Continue Partnership

Goodguys is one of many industry relationships the foundation has developed to help solve the technician shortage.

Valvoline Celebrates Female Service Center Employees

As women make up more than half of all drivers in the United States, Valvoline is taking steps to increase their vehicle care confidence.

ADAS Calibration Aborts

Knowing the common “hiccups” can save you time and money.