GM Tech Tip: Inspect and Ensure the Integrity of Wiring Harness Connectors

GM Tech Tip: Inspect and Ensure the Integrity of Wiring Harness Connectors

The first step in any type of electrical diagnosis is a visual and physical inspection of the wiring harness connectors for integrity. Many times, the vehicle may be repaired just by disconnecting and reconnecting the connectors. As with all repairs to wiring harness connectors and terminals, a pull test of the terminals within the connector should be performed. A pull test is performed by ....

Models affected: 2006 and prior General Motors cars and light-duty trucks, 2003-’06 HUMMER H2, 2006 HUMMER H3 and 2005-’06 Saab 9-7X.

When servicing a vehicle for any type of customer concern — such as miscellaneous DTCs, intermittent driveability concerns, hard start, no start, incorrect gauges, inoperative air conditioning systems, service engine soon lamps illuminated, 4WD lamp illuminated, instrument panel gauges inoperative or cruise inoperative — the following steps are imperative. Inspect and ensure the integrity of all related wiring harness connectors. If the wiring harness connectors are not properly put together or engaged before they are locked together, numerous types of intermittent conditions may occur, which may include any of the symptoms listed above and possibly others.

The first step in any type of electrical diagnosis is a visual and physical inspection of the wiring harness connectors for integrity. Many times, the vehicle may be repaired just by disconnecting and reconnecting the connectors. As with all repairs to wiring harness connectors and terminals, a pull test of the terminals within the connector should be performed. A pull test is performed by inserting the proper size terminal test tool (not a paper clip) into the terminal to determine whether or not the terminal is making good contact, or whether the terminal has been damaged from the prior improper connection or lack of connection.

Note: Most terminals used in current module connectors (ECM, BCM, EBTCM and the like) are small 0.64 mm sq. terminals and can be damaged by probing with the wrong tool.

The J 3561 6-64A or B probe has been designed for these terminals that may be both a round or square design. For example, if the Connector C2 of the engine wiring harness to the powertrain control module (PCM), for the 2.2L-equipped Cavalier or Sunfire is not properly seated into the PCM:
• The cam lock lever may close, however improperly;
• The cam lock lever may even snap out of position; or
• The vehicle may have an intermittent condition with any one of the components which are controlled or monitored by the PCM.

The cam lock lever is designed to pull (or assist) the connector into its final position once it has been pressed straight into the PCM header past the initial detent, allowing the lever to be moved into the locked position. It is not only a retainer, but an assist during the connection process. When the wiring harness connector is properly connected to the PCM, a snap will be heard when the connector is in position to be fully seated. The cam lock lever may then be closed. The cam lock lever will then do its designated job as both an assist and to ensure the connector does not come apart due to vibration or other types of conditions found in vehicles as they travel down the highway.

Remember, if a terminal (metal) or the connector (plastic) is damaged, they should be replaced. DO NOT replace the complete wiring harness assembly. Some harnesses are now on order restriction since most harness damage can be repaired.

Terminals and terminal removal tools are in the J 38125 Terminal Repair Kit and pigtails or complete connectors can be obtained through normal parts ordering procedures or from GMSPO and Saab PDC along with tape or conduit.

Courtesy of Mitchell 1.

For more information on Mitchell 1 products and services, automotive professionals can log onto the company’s website at www.mitchell1.com.

You May Also Like

Mercedes-Benz ABC Suspensions

The system provides great ride & handling, but it can be complicated to service if you do not have the right training.

Mercedes-Benz uses two different adjustable suspension systems in its vehicles – Airmatic and Active Body Control (ABC). Airmatic, as the name implies, is its air suspension system which we discussed back in April of this year. ABC uses hydraulic fluid at tremendous pressures to actively change the stiffness of the springs inside the shock assemblies, changing vehicle dynamics and ride height. This can be done automatically based on sensor inputs and module programming, or at the push of a button located near the shifter.

Regenerative Braking Service

Regenerative braking takes the forward motion of the vehicle and turns it into electrical energy.

Toyota Prius Battery Codes P0A7F, P2011 and P0A80

A second generation Toyota Prius is at least 12 years old and batteries may need to be replaced. Here’s what the codes mean.

Air Ride Diagnostics: Reservoirs and Compressors

The secret to diagnosing air ride problems is knowing what criteria the system uses to regulate the compressor/reservoir and having the right tool.

Mazda SkyActiv Engine Service Tips

These engines have been reliable, but there are four pattern failures you might see.

Other Posts

Audi TFSI/FSI: Oil Consumption And Carbon Buildup

Technical Service Bulletins can be valuable in helping solve vehicle problems. But sometimes, it takes multiple TSBs to find a pattern failure or the “root cause” of a problem. In the case of the Audi/VW 2.0L Fuel Stratified Injection (FSI) engine introduced in 2006, three problems related to engine carbon and fuel issues are connected

Solving Intermittent Overheating

New cooling systems anticipate and influence changes in coolant temperature.

Now Available – March’s Digital Edition of ShopOwner

The March issue includes technical and management content and is free to download.

Today’s Fuel Pressure Diagnostics

Direct injection pressure is measured with sensors, and the signals are used to determine pump speed and/or volume.