Eyeball Estimates: Stop Using Percentages if You Cannot Show Your Work!

Eyeball Estimates: Stop Using Percentages if You Cannot Show Your Work!

I have been seeing a lot of estimates recently that project how much “life” is left in the brake pads. This number is often expressed as a percentage. While I do realize that it is a number most customers might be able to understand, it is misleading and often inaccurate.

The typical estimate says, “20 percent of life left”, or “20 percent of the material left.” What really troubles me is that there is no actual “work” shown on the invoice telling how many millimeters of material is actually left on the backing plate. The “percentage” is just an “eyeball estimate.” This estimate is by no means accurate, and if you asked other technicians, you would get different numbers every time.

This is scary, and this practice could get shops in trouble.

Showing Your Work
In math class we were always asked to “show our work,” so why should it be any different when we are inspecting a critical system like the brakes?

If you were to properly estimate the percentage of material worn on a brake pad, you would first have to know how much was there in the first place. This number is near impossible to find in books or on a database. Sure you could get a new set of pads for the vehicle and use that as a reference, but would you really want to keep that many pads around for just reference?

No brake pad is designed to be worn down to the backing plate. Using the backing plate as the zero point is not a good idea, and gives the customer the wrong impression.

Every vehicle has a “minimum wear specification” for the brake pads. This number is typically between two and three millimeters. At this point, caliper piston travel maybe too excessive, or the friction material attachment method may lose its effectiveness and cause the friction material to shear away from the backing plate.

Also, some pad manufacturers change the friction material formulation in the lower layers to enable the material to flow through the holes in the backing plate. This may cause the material to wear faster than the upper layers. This makes estimating the last 20 percent of the material’s life impossible.

The Right Way
The right way to communicate to a customer if their pads are in need of replacement is to use OEM minimum pad wear specs. These specifications can be found on any repair computer based information database or in a repair manual. For the most part, these specs are between two and three millimeters. But, some vehicles will have a higher specification, like on multi-piston calipers. You should always measure the pad with the most wear.

The minimum wear specification is measured from the backing plate to the lowest point of wear on the friction’s face that contacts the rotor. On some vehicles, this can be measured without disassembly.

The best tool, in my opinion, to use is a metric tapered bore gauge. This tool can be found at most automotive tool stores for less than $15.00. This ruler’s tapered width corresponds to the numbers on the side that are in millimeters. It is like measuring the gap of a spark plug.

This measurement is very credible in the eyes of the customer because you can tie it to an OEM specification.

Stop Using the Eyeball!
I love a percentage just as much as the next guy. But, “eyeballed” percentages should not be used when inspecting brakes. It is a practice that should be stopped right now!

You May Also Like

ASE Education Foundation, Goodguys Continue Partnership

Goodguys is one of many industry relationships the foundation has developed to help solve the technician shortage.

The ASE Education Foundation and Goodguys Rod and Custom Association (Goodguys) are continuing their partnership and will conduct educational awareness seminars at select Goodguys events throughout the 2024 season.

Since its inception, the ASE Education Foundation has brought industry and education together to develop entry-level technicians. Goodguys is one of many industry relationships the Foundation has developed to help solve the technician shortage.

BMW Diagnostics: Low Airflow After Cabin Filter Replacement

Models:  F97 X3 M  F98 X4 M G01 X3 G02 X4 G20 3-Series SITUATION After replacing the microfilter during a previous service, the customer notices that the ventilation system airflow rate is noticeably less. This leads to perceived lower cooling power. The customer may also notice that external odors enter the vehicle. Related Articles –

Volvo Modular Engine Service

The Volvo Modular Series engine outlasted Ford and was retired by Geely. The Volvo modular design that can have four, five or six cylinders made its debut in 1990 in the 960 sedan as a six-cylinder and never stopped improving. Related Articles – How To Service BMW Tire Monitor Systems – VW DSG Maintenance –

BMW Cooling System Problems

Let’s take a closer look at this unique water pump, how to replace it efficiently and what other components should be replaced along with it.

Audi Active Suspension Service

The key to servicing these systems is proper information and understanding precisely how these systems operate.

Other Posts

Valvoline Celebrates Female Service Center Employees

As women make up more than half of all drivers in the United States, Valvoline is taking steps to increase their vehicle care confidence.

BorgWarner Announces Plan to Reduce Supply Chain Emissions

A partnership with Manufacture 2030 will support BorgWarner in reaching its Scope 3 emissions reduction goal.

Snap-on Continues to Offer Free Weekly Product Training Sessions

The online training and question and answer sessions are free of charge.

AMSOIL Introduces New OE 0W-40 100% Synthetic Motor Oil

The new OE 0W-40 is primarily for newer RAM HD trucks equipped with the 6.4-liter Hemi engine.