How Catalytic Converters Operate: Emissions

Understanding Catalytic Converters

When servicing catalytic converters, it's important to have a basic understanding of how they operate.

To begin, an internal combustion engine creates heat energy by igniting a mixture of gasoline and atmospheric oxygen with a high-voltage spark. Unfortunately, a residual quantity of hydrocarbons (HC), carbon monoxide (CO) and nitrogen oxide (NOx) are left over after combustion. Consequently, a catalytic converter uses precious metals like platinum as a catalyst to convert harmful pollutants like HC, CO and NOx into harmless gases like oxygen (O2), carbon dioxide (CO2) and water (H2O). Since a catalyst will accelerate a chemical reaction without being consumed by the process itself, the catalytic converter will theoretically last forever. In reality, catalytic converters eventually succumb to heat stress and contaminants from coolant and engine oil additives.

Converter Types

“Direct-fit” catalytic converters are of three basic types: two-way, three-way and three-way plus oxidation converters. Two-way “oxidation” converters were used up to 1980 and are designed to eliminate HC and CO. Three-way converters are designed to eliminate NOx as well as HC and CO. A three-way plus or “dual-bed” converter allows atmospheric air to be injected between the three-way catalyst and an extra oxidation bed to further clean the engine exhaust.

 The precious metals used as catalysts are distributed in molecular form over a rough-surfaced ceramic wash coat covering the metallic honeycomb substrate. The effectiveness of the converter is basically determined by the amount of precious metals present on the honeycomb substrate. Consequently, it’s very important for suppliers and technicians alike to meet EPA requirements by selecting the correct catalytic converter for the application.

The Catalyst Monitor

The catalyst monitor or self-test runs only once after the engine is started and driven. Basically, the engine control module (ECM) uses a mathematical algorithm programmed into the ECM software to compare the electrical activity of the upstream oxygen sensor (before the converter) with that of the downstream oxygen sensor. When the electrical activity of the upstream and downstream oxygen sensors doesn’t meet programmed parameters, a diagnostic trouble code (DTC) P0420 and/or P0430 is stored in the ECM’s diagnostic memory and the orange “Check Engine” warning light is illuminated. 

Because the catalyst monitor is mathematically-based, attempting to diagnose a converter by comparing inlet and outlet temperatures or by using an exhaust gas analyzer will not yield valid test results. When a P420/430 diagnostic trouble code (DTC) is present, the professional technician should check for related ECM calibration update bulletins before replacing a catalytic converter. In many cases, reprogramming the PCM might solve a stubborn P420/430 DTC issue.

Typical Causes Of Catalyst Failure

An ignition system misfire is the most common cause of catastrophic converter failure. When a misfire occurs, the catalytic converter overheats because combustion takes place in the converter rather than the engine. When the converter exceeds an operating temperature of about 1,300 degrees F, the converter substrate begins to melt and cause exhaust restriction. Common failures also include a catalyst suffering from an external impact or being contaminated by coolant from leaking cylinder head gaskets.

When To Sell Catalytic Converters 

The auto manufacturer’s original equipment (OE) catalytic converters are initially covered by an EPA-mandated 8-year, 80,000-mile warranty. A new aftermarket catalytic converter can be installed only if the original is missing, fails a state or local emissions inspection program or is plugged, leaking, or has sustained physical damage. Most vehicles require catalytic converter replacements when an illuminated CEL indicates a converter failure or if the engine itself has failed an exhaust emissions test. To pass an exhaust emissions test, the converter must meet the exact configuration and capacity as specified by the OEM. Due to adopting more stringent emissions standards, many other states are now requiring catalytic converters that meet California specifications. When selling any catalytic converter, remember to fill out the paperwork as required by state and local agencies.

You May Also Like

Top 10 Brake Mistakes

Here are the top 10 brake mistakes technicians can make.

1. Not cleaning the brake slides and hardware: Just slapping new pads and abutment clips where the old ones once resided never works. The caliper bracket slides need to be clean and free from rust. Don’t get overly aggressive with the wire brush. Some automakers are using anti-corrosion coatings and surface treatment on the brake caliper bracket lands. If brake cleaner and a nylon brush can’t tackle the deposits, you might be making the corrosion worse by using a wire wheel or file.  

Fine-Tuning Your Wheel Balancing Process

The first step to a smooth ride and well-balanced tire has nothing to do with the balancer.

Drilled and Slotted Rotors

There’s real science behind the location of holes, slots and grooves in today’s brake rotors. Plus, they look great too.

Laying Out Your Shop for ADAS/EV Repairs

With so many vehicles equipped with some form of ADAS, rethinking your electronics layout or plan might be in order.

Air Ride Suspension Diagnostics

The key to understanding the embedded logic of air ride systems is using service information.

Other Posts

How-to Complete Emissions Monitors Faster

This video will focus on how a product like CAT COMPLETE can improve the chances of completing the monitors faster. This video is sponsored by Rislone.

Confusion, Carcasses and Catalytic Converters

Dealing with warranty return headaches starts with fixing the real failure first.

Forecast: 80% Drop In U.S. Transportation Emissions By 2050

NREL’s study highlights rapid adoption of zero-emission vehicles as crucial for an 80% emissions reduction.

Understanding Emissions

Modern EVAP systems are selective with how they vent vapors back into the engine. Sponsored by Standard.