Cylinder Head Repair

Diagnostic Solutions: Cylinder Head Repair

Cylinder head gasket failures are one of the most common mechanical issues facing today's modern import technician. One reason head gasket failures are common is because the cylinder head gasket itself can become a wearing part. Since the aluminum cylinder head expands at a slightly higher rate than the cast-iron cylinder block, the cylinder head actually slides a few thousandths of an inch across the gasket surface as the engine warms up to operating temperature.

2.jpg” border=”0″ ” align=”right” alt=”photo 2: the absence of light shining underneath this precision-round straight edge indicates that the cylinder head is straight. although warping of 0.002” per cylinder is the maximum generally allowed, the tolerance on some modern engines is much less.”/>

If the cylinder head is warped beyond specification, the cylinder head must be straightened or replaced. In addition, an experienced cylinder head shop will check for cracks in the cylinder heads that are indicative of a severe overheating condition.

 

CYLINDER HEAD RECONDITIONING

In my experience, choosing between reconditioning and replacing a cylinder head depends upon the individual application. Some cylinder head castings are so thin that they can’t be reliably repaired. In other applications, a fully equipped cylinder head repair shop can weld cracks and straighten aluminum cylinder heads to specification.

A shop should also be able to replace hard valve seats, restore valve guides and resurface cylinder heads to OEM specifications. Keep in mind that rough mill cuts will quickly ruin most modern cylinder head gaskets.

In contrast, late-model cylinder heads require a mirror finish to prevent scuffing the cylinder head gasket during warm-up. See Photo 3.photo 3: quality is in the details. the edges of this combustion chamber have been chamfered to eliminate the possibility of a sharp casting edge causing destructive preignition.

When stock is removed from the cylinder head gasket surface, camshaft timing will be retarded because the center-to-center dimension between camshaft and crankshaft is reduced. In some cases, thicker head gaskets or head gasket shims are available to compensate for stock removal from the cylinder head. If no method of compensating for stock removal is available, the cylinder head should be replaced. On the other hand, many cylinder head shops like to remove a small amount of stock to remove corrosion pitting and wear damage from the head gasket surface. In most cases, the amount of change in camshaft timing is negligible and causes no noticeable change in engine performance. See Photo 4photo 4: an adjustable aftermarket camshaft sprocket will restore correct camshaft timing on this toyota 22r engine.

 

CYLINDER HEAD CLEANING

Perfectly clean gasket surfaces on the cylinder head and block are essential to a successful cylinder head gasket replacement. Because gaskets tend to bake onto metal surfaces, gasket removal can be somewhat challenging.

Never use sharp metal instruments that can scratch a gasket surface or use rotating abrasive-fiber pads that can gouge irregularities into precision-machined surfaces. Abrasive pads can also shed abrasive fibers into the engine lubrication system. During cold start-up, high oil pressure often pushes these fibers through the oil filter bypass valve and allows them to embed into soft engine bearings. See Photo 5. Photo 5: Cleanliness is extremely important in making a reliable gasket repair. The surface on this Toyota 22R engine block has been resurfaced to remove pitting and wear marks.

The most preferable method for cleaning aluminum surfaces is using a chemical gasket ­remover and a plastic scraper available from the paint section of your local hardware store. I’ve also used hardwood clothes pins as well as brass windshield scrapers to remove hardened residue from machined aluminum surfaces. In some cases, hardened gaskets can be scraped away with single-edge razor blades, but such a procedure requires care and patience to avoid damaging the cylinder head.

 

CYLINDER HEAD GASKETS AND BOLTS

To accommodate cylinder head expansion, modern cylinder head gaskets are usually either of the graphite-composite or the multi-layer steel (MLS) types, neither of which require re-torquing. Because it’s hard to make general statements about modern head gasket installations, it’s extremely important to read the enclosed instructions.

Although some applications do require a dab of sealant on cylinder head bolt threads and at various metal-to-metal joints, many MLS gaskets are already coated with a sealant at the factory. In most cases, applying additional sealants to a new head gasket can cause a loss of bolt torque retention as the engine warms up.

In addition, many modern cylinder heads require torque-to-yield (TTY) bolts that should be replaced with the new head gasket. Because these bolts are stretched beyond their limits of elasticity to achieve maximum clamping force, bolt torque is rated in degrees of rotation rather than by the conventional foot-pound or Newton-meter values. In addition, many new cylinder head bolts are pre-lubed out of the box.

If conventional bolts are being re-used, it’s important to lubricate them according to manufacturer’s instructions or with a light coat of 30w non-detergent motor oil. Oils containing friction modifiers will not provide correct torque values on cylinder head bolts.

Last, it’s important to prevent engine block damage by blowing any liquid residue or debris out of the bolt holes with low-pressure compressed air. The block threads on aluminum engines must also be inspected for pulling, especially if the engine was overheated. Engine block thread repair kits are generally available through OE and aftermarket sources.

 

ENGINE WARM-UP

Once assembled, it’s important to bleed air from the cooling system according to recommended procedures.

First, make sure that the engine is filled to its rated capacity with the correct coolant. Next, allow the engine to go through at least one warm-up and cooling cycle to allow additional coolant to be drawn into the cooling system and to check for leaks.

If coolant is circulating through the system, the upper radiator hose and radiator will feel hot to the touch. If the radiator feels cool after the engine reaches operating temperature, air might be trapped under the thermostat. If in doubt, run the engine through another heating and cooling cycle to draw in more coolant.

Last, if the coolant remains at the recommended level in the coolant reservoir, the vehicle is ready to release to the customer.

 

 

You May Also Like

UniClutch Launches Clutch System in the United States

From Australian manufacturer Clutch Industries, UniClutch is a clutch system that delivers uncompromised performance.

UniClutch and UniClutch Sport will be the first iterations of this system to launch in the U.S. UniClutch's dual core technology significantly boosts torque capacity without compromising drivability. Its one-of-a-kind, patented and adaptable design fits a multitude of vehicles, simplifies inventory management, expedites clutch replacement time, and lessens common installation problems. Compared to UniClutch, UniClutch Sport offers a further 15% more torque capacity and a sport-tuned pedal feel for more serious enthusiasts. These features create a clutch system with mass appeal for consumers and aftermarket businesses alike, as the industry grapples with a continuously challenging supply chain and the need to find labor efficiencies.

Automotive Hall of Fame Announces Class of 2024 Inductees

Six honorees whose efforts helped shape the automotive and mobility marketplace will be recognized.

Castrol Turns 125, Debuts New Market Strategy

As part of the new strategy, Castrol will explore opportunities in battery thermal management, digital and service solutions and data center immersion cooling.

Advance Auto Parts Announces ‘National Battery Day’ Promo

DieHard battery giveaways and complimentary battery testing will be part of nationwide festivities held on Feb. 18.

FCS Introduces 18 New Numbers in February

The new release includes 4 shock absorbers and 14 suspension struts.

Other Posts

Tenneco Introduces Add-On Valve Technology 

The company says the RideRefine SDD valve brings new levels of versatility, tunability and comfort to passive damper performance.

AP Emissions Releases New Part Numbers for February

AP Emissions Technologies has released 12 new SKUs that cover six million VIO in the month of February.

Lumileds Debuts New Philips Automotive Lighting Website

The site features an entirely new design that brings together the full breadth of the Philips portfolio of automotive lighting and accessories in North America.

Standard Motor Products Expands Emission Control Program

SMP’s program features more than 3,500 parts, including EVAP, EGR and positive crankcase ventilation products.