Diagnosing Exhaust Gas Recirculation (EGR)

Diagnosing Exhaust Gas Recirculation (EGR)

Exhaust gas recirculation is the dilution of the air/fuel mixture to control amounts of exhaust gas. Since exhaust gas does not burn, this lowers the combustion temperatures and reduces NOx emissions from the engine. At lower combustion temperatures, very little of the nitrogen in the air combines with oxygen to form NOx. Most of the nitrogen is simply carried out with the exhaust gases.

By Carl Fedele, contributor

Emission controls on cars and trucks have one purpose: to reduce the amount of pollutants and ­environmentally damaging substances released by ­vehicles.

In this column we will take a look at exhaust gas recirculation (EGR), one of the four major basic system control components used on all ­systems today.

In subsequent issues, we will highlight the other three main internal combustion engine emission system control components — positive crankcase ventilation (PCV), air injection reactors (AIR) and the catalytic converter.

Exhaust gas recirculation is the dilution of the air/fuel mixture to control amounts of exhaust gas. Since exhaust gas does not burn, this lowers the combustion temperatures and reduces NOx emissions from the engine. At lower combustion temperatures, very little of the nitrogen in the air combines with oxygen to form NOx. Most of the nitrogen is simply carried out with the exhaust gases.

For consistent driveability, it is desirable for the amount of exhaust gas flow to be proportional to the throttle opening. Driveability is also improved by stopping EGR when the engine is started up cold, at idle and at full throttle.

Early EGR
The first EGR valve appeared in 1973 on General Motors cars. Bolted to the intake ­manifold next to the carburetor, it had ports to the intake and exhaust manifolds. It had a diaphragm that pulled open a valve stem, which allowed exhaust to enter the intake manifold when ported vacuum was applied to it. Ported vacuum increases with throttle opening. A thermal vacuum switch prevented vacuum from reaching the EGR during cold engine starts.

This system, however, had problems. It would often open too soon or too much, which caused a hesitation with acceleration as massive amounts of recalculated exhaust hit the combustion chamber. Many people simply disconnected it when it began to cause a problem.

By 1975, if you unplugged an EGR valve, you’d end up having an engine ping driveability complaint.
Manufacturers of that era experimented with vacuum orifice restrictors and vacuum delay valves to try to find a happy medium between clean air and performance.

By 1981, closed loop computer controls were in place. EGR flow was now more carefully controlled with dual diaphragm and backpressure EGR valves. The flow of vacuum was further controlled by solenoids that blocked the vacuum ported until certain criteria were met, such as engine temperature, rpm and manifold absolute pressure (MAP). As the vehicle manufacturers began to use these complex schemes with vacuum amplifiers, delay valves and solenoids, they added a lot of “spaghetti” to the engine compartments.

Plastic vacuum connections would break or rot with age and were not reliable. Vacuum diagrams were invented and became essential to the smog driveability technicians of the day. As these systems evolved, they had fewer parts and less vacuum tubing. This was achieved by the use of pulse-width modulated EGR solenoids. The PCM controlled EGR flow through the use of these solenoids to modulate vacuum to the EGR valve instead of just turning it on or off periodically.

Once the PCM receives its inputs, such as rpm, throttle angle, coolant temperature and MAP, it then calculates a response based on the software program that is embedded into it. Next, it makes its decision and sends a command in the form of a pulse-width modulated signal to turn the EGR solenoid on and off rapidly. The EGR solenoid has two vacuum nipples. One side gets either manifold or ported engine vacuum. The other nipple goes to the EGR valve. Its default position is to block vacuum to the EGR valve. A vent is incorporated to bleed off vacuum when the solenoid is being pulsed. Vacuum flows to the EGR in rapid on-off pulses as the solenoid is commanded by the PCM.

With each succeeding year, EGR designs in OBD I systems became more refined. The California Air Resources Board (CARB) liked GM and Chrysler’s onboard diagnostic systems. In 1988, CARB required that all cars sold in California be equipped with an onboard diagnostic system and a check engine light to notify the driver of emission system failures. By this time, all manufacturers had to have an EGR system that was capable of alerting the driver if it wasn’t working. OBD I diagnostics and trouble codes were added in to flag opens, shorts and sticking solenoids.

OBD II requires that EGR systems be monitored for abnormally low or high flow rate malfunctions. The EGR is considered to be malfunctioning when an EGR component fails or a fault in the flow rate results in the vehicle exceeding the Federal Test Procedure (FTP) by 1.5 times. FTP is the government-mandated drive cycle smog test that all new cars must pass and adhere to.

Depending on the system it is used in, the design of the EGR valve may change. Often these design changes incorporate some of the system controls. Types of designs included positive backpressure, negative backpressure, ported and pulse-width modulation.

The positive backpressure EGR valve has a bleed port and valve positioned in the center of the diaphragm. A light spring holds this bleed valve open, and an exhaust passage is connected from the lower end of the tapered valve through the stem to the bleed valve. When the engine is running, exhaust pressure is applied to the bleed valve. At low engine speeds, exhaust pressure is not high enough to close the bleed valve. If control vacuum is supplied to the diaphragm chamber, the vacuum is bled off through the bleed port and the valve remains closed. As engine and vehicle speed increase, the exhaust pressure also increases. At a preset throttle opening, the exhaust pressure closes the EGR valve bleed port. When control vacuum is supplied to the diaphragm, the diaphragm and valve are lifted upward, and the valve is open. If vacuum from an external source is supplied to a positive backpressure EGR valve with the engine not running, the valve will not open because the vacuum is bled off through the bleed port.

In a negative backpressure EGR valve, a normally closed bleed port is positioned in the center of the diaphragm. An exhaust passage is connected from the lower end of the tapered valve through the stem to the bleed valve. When the engine is running at lower speeds, there is a high-pressure pulse in the exhaust system. However, between these high-pressure pulses there are low-pressure pulses. As the engine speed increases, more cylinder firings occur in a given time and the high-pressure pulses become closer together in the exhaust system. At lower engine and vehicle speeds, the negative pulses in the exhaust system hold the bleed valve open. When vacuum from an external source is supplied to a negative backpressure EGR valve with the engine not running, the bleed port is closed and the vacuum should open the valve.

Over time, electrical EGR units have been introduced into late-model vehicles.  
The most common of the three electrical EGR valves is the digital EGR units found mostly on GM vehicles.

A digital EGR valve contains up to three electric solenoids that are operated directly by the PCM. Each solenoid contains a movable plunger with a tapered tip that seats in an orifice. When any solenoid is energized, the plunger is lifted and exhaust gas is allowed to recirculate through the orifice into the intake manifold. The solenoids and orifices are different sizes. The PCM can operate one, two or three solenoids to supply the amount of exhaust recirculation required to provide control of NOx emissions. When testing a digital EGR valve, you can use a scan tool to activate the valve. The rpm should drop for each activation period. An EGR valve that’s plugged or not working will show no change.

According to Standard Motor Products, a manufacturer of emissions components, the EGR passages on the engines that have digital EGR valves are very prone to clogging.

EGR codes may be set that appear to indicate an electrical problem with the valve when in fact the real problem is clogged EGR passages in the intake manifold.

Another style is the linear EGR valve, which is basically a pulse-width modulated solenoid valve where the valve is spring-loaded closed. General Motors was the first to use these linear EGR valves. The computer varies the pulse-width command to the valve to control the amount of opening. A position sensor is integrated into the valve. The sensor generates a signal, very similar to a throttle position sensor, to indicate to the computer exactly how open or closed the EGR valve is. This feedback signal allows the computer to more accurately control the amount of EGR flow.

You also will encounter a stepper motor EGR valve, which is designed to work very similarly to GM idle air control motors that have been around for a long time. Here, the valve has two separate sets of coil windings. The PCM sends ­alternate, coordinated pulses to each winding to “step” the motor open or closed in small increments.

Unlike all other vacuum and electrical design EGR valves, stepper-type EGR valves remain in the last commanded position even when disconnected electrically. They do not “spring” closed when disconnected.

According to Standard Motor Products, the following tip is important — If the valve is disconnected electrically while open, then it will remain open and could lead to a technician incorrectly condemning the valve as defective.

When diagnosis of a negative backpressure EGR valve is needed, you must bring the engine up to normal operating temperatures. With the ignition off, disconnect the vacuum hose from the EGR valve and connect a hand-held vacuum pump to the fitting on the valve. Supply 18 inches of vacuum to the EGR valve and vacuum should hold steady for 25 seconds. If the valve does not open or cannot hold the vacuum, it must be replaced. If the valve holds steady, start the engine and the vacuum should drop to zero and the valve should close.

When diagnosis of a positive backpressure EGR valve is needed, the same basic test is used like the negative type but with opposite results. When the engine is idling, apply vacuum to the EGR valve and you should not be able to build up a vacuum in the valve and the EGR valve should not open. Turn off engine and disconnect the vacuum supply hose from the throttle body. Connect a long ­vacuum hose from the EGR vacuum port on the throttle body directly to the EGR valve vacuum port. Use a tee fitting to connect a vacuum gauge in the vacuum hose to the EGR valve, start the engine and bring it up to 2,000 rpm. Watch the vacuum gauge, vacuum should be present and the EGR valve should open.

On digital EGR valves, the resistance of the valve can be checked. By connecting an ohmmeter across the terminals on the valve, the windings can be checked for opens, shorts and high-resistance readings. If readings are not within specs, replacement of the EGR valve will be needed. Also, make sure that the EGR passages are not restricted or plugged. You will have to remove the valve to make this visual check. You can also use an exhaust gas analyzer to check an EGR system. Looking at the NOx readings at 2,000 rpm, the readings should be below 1,000 ppm.

You May Also Like

Mercedes-Benz Fuel Pumps

Mercedes-Benz has long been a pioneer of GDI.

Gasoline direct injection (GDI) may be one of the biggest automotive advancements from the past few decades, and has become all but standard in the internal combustion engines of today. GDI systems inject fuel at incredibly high pressures directly into the combustion chamber. The high pressure allows for better atomization of the fuel inside the cylinders, and much more precise control over the volume of fuel being injected.

Timing BMW VANOS N53 And N54 

To service them, you will need the appropriate toolset to lock the crank and camshaft.

Motor Mount Technology and Failures

Engines have noticeably changed in the past decade. Fewer cylinders, more power at lower RPM and more detectable vibration at idle are just a few of the differences in today’s engines. Related Articles – VW/Audi PCV Service – BMW Timing Chain Stretch Issues – Volvo AWD With Active On Demand Coupling With these changes, it

VW/Audi PCV Service

The PCV valve regulates the flow of gases from the crankcase.

BMW Timing Chain Stretch Issues

Over the past decade, BMW and many other import automakers have had issues with timing chain stretch. When most BMW owners hear the phrase “timing chain stretch,” they assume that the gears on the crankshaft and camshaft sprockets have pulled on the chain, causing the links to lengthen like a rubber band. It is not

Other Posts
How Modern Car Sensors Optimize Performance and Emissions

Explore how modern cam and crank sensors are revolutionizing engine performance and emissions control.

Don’t Miss The July Digital Edition of ShopOwner

The July issue includes technical and management content and is free to download.

Battery Charging and Diagnostics

Today, it requires more than just a multimeter to diagnose the battery and alternator.

Toyota Regenerative Braking System

The brake system of a hybrid may have multiple components to perform regenerative braking and pedal simulation.