Chassis – Ride Control Diagnostics From Tire Wear

Chassis – Ride Control Diagnostics From Tire Wear

Learning how to read the tire and communicate your findings is the key to ride control.

Tire wear patterns are visual representations of how the vehicle is performing and how owners maintain their vehicle. Tread patterns reveal the condition of alignment angles, suspension components and ride control components. Learning how to read the tire and communicate your findings to your customers is the key to selling ride control.

What is tire wear? The perfectly worn tire would have a perfect contact patch with the weight evenly distributed shoulder to shoulder. But, to get ideal tire wear, its toe, camber and caster angles would never change. In the real world, a tire must go around corners and deal with uneven road surfaces. The suspension and ride control system must strike a balance between handling and comfort. Engineers can design the suspension so the geometry minimizes uneven wear, but they can’t design for worn components.

Therefore, a tire’s contact patch is controlled by the geometry of the suspension. The movement of the body and suspension is controlled by the shocks, struts and springs. If the ride control can’t control the movement or body or suspension, the tires will suffer.

The geometry and pickup points of a suspension change in relation to the road as the vehicle’s pitch and yaw change. Also, angles like caster, camber and toe influence each other as the driver turns the steering wheel. Another factor is flex, or compliance, in the suspension and steering system. If a bushing is soft, it will compress and effectively change the suspension pickup point.

If you get a customer in your shop who is looking for new tires because the old set is worn out, check the set of tires for the below conditions to determine if they also need new shocks, struts or springs.

Inner Edge Wear

  • Alignment
  • Ride height
  • Leaking air ride
  • Worn springs
  • Worn ride control

The shoulder of a passenger car tire is designed to hold up to a lot of abuse. But, the shoulders are the first area to wear if there is an issue with how the tire makes contact with the road.

Inner-edge wear is typically related to negative camber and the wheels being toed out. Camber and toe change with the vertical movement of the suspension and the movement of the body. This helps improve traction when the vehicle is cornering.

If a vehicle has weak springs and can’t keep the vehicle at the proper ride height, negative camber and a toed out suspension angle can occur.

Outer Edge Wear

  • Weak or worn ride control
  • Alignment issues
  • Broken sway bar links

If the outer edge of the tire is worn, it is a sign that the sway bars, springs and dampeners can’t control the movement of the body. When a vehicle goes into a turn, the body can lean. It can be worse on vehicles with a high center of gravity like crossovers, SUVs and pickup trucks.

When the body of a car or truck leans, it can induce positive camber on the outside wheel. Positive camber and the transferred weight scrub the outer edge of the tire.

Both Edges

  • Low tire inflation (Check TPMS)
  • Weak ride control
  • Broken sway bar links
  • Ride height

If the shocks, struts and springs are so far gone, the body will sway more than usual going around a corner. The body lean will cause enough positive and negative camber to wear the edges of the tires. The other problem could be the sway bar and the links. In some cases, it might just be a lack of rotation.

Tire Feathering

  • Ride height
  • Worn springs
  • Poor alignment

The indicator of excessive positive or negative toe angle is a tire feathering or scuffing that can be detected by stroking your fingertips across the edge of each tread bar or block. A feather edge on the inside of the tread bar indicates excess toe-in, while a feather edge on the outside indicates toe-out. Because toe angle is affected by changes in camber and caster angles, it’s always the last angle to be adjusted during the wheel alignment process. In addition, any change in camber or caster angles will immediately change the toe angle. Toe angle geometry can also be greatly affected by changes in suspension height, like an uncalibrated air ride system.

Scalloped Tires

  • Worn ride control
  • Lack of rotation

Cupped or scalloped dips appearing around the surface of the tire tread could indicate loose, worn or bent suspension parts. Worn shock absorbers or unbalanced tires can also cause cupping, but the cupping would typically be more indicative of a concentric pattern. Shocks and struts are the most likely culprit because they provide dampening force to control tire movement. When the tires move excessively, the scalloped pattern can appear. A lack of rotation can cause this type of condition on the rear tires.

Spring and Tire Health

The health of a spring determines the health of the tire. A little bit of life is taken out of a spring when it is compressed and the energy is released. It’s not the amount of travel that matters, but the frequency of the cycles. Over the years, the flexing and frequency will cause fatigue that can be measured in a loss of ride height that can cripple the alignment angles.

But, some springs can fatigue and still not have a significant loss of ride height. These springs can have a progressive design and use coil geometry to give a smooth ride in a straight line, but become stiffer as the body and chassis start to transfer weight. The only way to inspect these types of springs is with a test drive and visual inspection of the spring and tires.

Shock and Strut Wear

Over time, shocks can lose this charge of gas. The gas prevents foaming of the oil in the shock or strut. When this happens, the shocks can overheat and fade. In this state, the shock or strut can’t control the suspension and body, this leads to abnormal tire wear.

The gas leaks out because the seals for the gas chamber wear out and leak, or the “pillow” filled with nitrogen ruptures. Gas can escape out of the seals around the rod easier than oil.

You May Also Like

Top 10 Brake Mistakes

Here are the top 10 brake mistakes technicians can make.

1. Not cleaning the brake slides and hardware: Just slapping new pads and abutment clips where the old ones once resided never works. The caliper bracket slides need to be clean and free from rust. Don’t get overly aggressive with the wire brush. Some automakers are using anti-corrosion coatings and surface treatment on the brake caliper bracket lands. If brake cleaner and a nylon brush can’t tackle the deposits, you might be making the corrosion worse by using a wire wheel or file.  

Fine-Tuning Your Wheel Balancing Process

The first step to a smooth ride and well-balanced tire has nothing to do with the balancer.

Drilled and Slotted Rotors

There’s real science behind the location of holes, slots and grooves in today’s brake rotors. Plus, they look great too.

Laying Out Your Shop for ADAS/EV Repairs

With so many vehicles equipped with some form of ADAS, rethinking your electronics layout or plan might be in order.

Air Ride Suspension Diagnostics

The key to understanding the embedded logic of air ride systems is using service information.

Other Posts

Now Available – March’s Digital Edition of ShopOwner

The March issue includes technical and management content and is free to download.

Mercedes Airmatic Suspensions

Diagnostic tips to aid your repair efforts.

TPMS Curve Balls for European Vehicles

You May Think You Know the Cause of a TPMS Problem, Until One Car Defies It Related Articles – CVT Transmission Service – Charging For TPMS Service – Audi E-Tron Brake Jobs When you think you know everything about tire pressure monitoring systems (TPMS), there will be a car or truck that pulls into your

CVT Transmission Service

Like any automatic transmission, the condition and level of fluid in a CVT unit will determine the performance.