Catalyst Efficiency Monitors: O2 Sensors PCM?

Catalyst Efficiency Monitors: What Are The O2 Sensors Telling The PCM?

The catalyst efficiency monitor verifies that the catalytic converter is operating at a high enough efficiency rating to keep exhaust emissions within the predetermined values. The PCM compares the signals from the upstream and downstream oxygen sensors to determine the state of the converter. These "tests" are called readiness monitors.

The catalyst efficiency monitor verifies that the catalytic converter is operating at a high enough efficiency rating to keep exhaust emissions within the predetermined values. The PCM compares the signals from the upstream and downstream oxygen sensors to determine the state of the converter. These “tests” are called readiness monitors.

Continuous And Non-Continuous Readiness Tests

A monitor is a section or segment of an operation that the vehicle normally performs or one that needs to be done to verify a certain aspect or condition of the vehicle. There are two basic types of readiness monitors: continuous and non-continuous. Continuous monitors are constantly tested and evaluated while the engine is running. The non-continuous monitors need to have certain conditions met before a test can be completed.

Some operations can be either continuous, non-continuous or both, and can be checked during both types of monitors: such as a misfire or fuel system issue. Non-continuous monitors will differ between gas and diesel engines as well.

A newer vehicle can report its emissions monitor status during its current driving cycle. These monitors start from the beginning whenever the monitoring cycle meets the criteria to run a readiness test. Older cars might not support this feature. Because the monitors are a self-check routine that the driver does not have to initiate, the best way to get them ready to perform a self-test is to drive the vehicle. Although, driving alone won’t meet all the needed conditions. There are a few requirements that vary from manufacturer to manufacturer.

Make sure that the MIL (Malfunction Indicator Light) is not commanded on. If there are any efficiency or related codes stored or even a pending diagnostic trouble code, they can prevent a monitor from ever running or completing.

Be sure that you have enough fuel in the car. Some monitors, for instance the EVAP monitor, may require the fuel level to be between 35% and 85% to initiate the diagnostic testing.

Lastly, you have to complete a “drive cycle.” The drive cycle lets the car run its on-board diagnostics. This allows the readiness monitors to go through their preset diagnostic routine.

Check the manufacturer’s specifications for a drive cycle to get the exact requirements of the vehicle on which you’re working. However, the below generic drive cycle usually works on most vehicles.

Generic Drive Cycle

Pre-plan a driving route that will allow you to bring the vehicle up to highway speeds and also allow you to slow the vehicle down on a long coast. Be sure to have at least 51% in the fuel tank, and the outside ambient temperature is not below freezing or above 110 degrees.

The drive cycle begins from a cold start. This means that the coolant and air temperatures are within 10 degrees of each another. (This condition can be achieved by letting the car sit overnight). The ignition key must be in the OFF position before the cold start. Otherwise, the heated oxygen sensor diagnostic may not run. Start the engine and let it idle for about two to five minutes, with the A/C and rear defroster on (if equipped).

Turn the A/C and rear defroster off, and bring the vehicle speed up to at least 55 mph under moderate and constant acceleration. Hold the speed steady for a minimum of three minutes. Gradually slow the vehicle, without braking, to about 25 mph. Do not depress the clutch if you are running with a manual transmission. Accelerate up to highway speeds (higher than 55 mph) using no more than about ¾-throttle. Hold that speed steady for five minutes.

Slow down, without braking, until the vehicle is below 25 mph and come to a gradual stop. At this point, the internal monitor tests should run.

Keep in mind, the non-continuous monitors may not catch a problem until the vehicle has been driven several times and the conditions are right to detect the fault. Consequently, any time you’re troubleshooting a catalyst efficiency problem, it’s very important to use a scan tool that can tell you if all the readiness monitors have run or not. If one or more monitors are not ready, the vehicle will have to be driven under the correct conditions to make the monitor set. Then, and only then, will you get an accurate diagnosis.

What Is Efficiency?

The converter has an efficiency rating that is computed by the vehicle’s manufacturer. The efficiency of the converter is tied to the fuel trim of the engine. The fuel trim is monitored by the O2 sensors and is constantly adjusted by the PCM. This helps to keep the converter at the correct temperature for the most efficient operation. One of the roles of the converter is to store a certain amount of oxygen in it. If an engine is running too rich, it cannot store oxygen. If it is running too lean, the oxygen levels may prevent the converter from reaching its optimal heat range.

A rich condition means less oxygen. A lean condition means excessive oxygen. A rich condition would mean the PCM wants to lean out the fuel mixture. Meanwhile, a lean condition would mean the PCM wants to try and increase the fuel mixture.

The stoichiometric value of the fuel-to-air mixture is 14.7 to 1 (by weight). For the converter to operate correctly, the stoichiometric value needs to be reached so that the catalyst can react with the oxygen and reach the proper operating temperature. The catalytic converter begins to function at 400 to 600°F. The normal operating temperature can range up to 1,200 to 1,600 degrees.

Converter efficiency can be checked with a scan tool as well as by watching the O2 sensors switching between rich and lean. Lab scopes can also be used to monitor the switching. Once the efficiency drops below a specified level and other criteria are met, an efficiency code will be set.

Most converters start out at about 99% efficiency when new, and quickly taper off to about 95%. As long as the efficiency doesn’t drop off more than a few more percentage points, the converter will do a great job of cleaning up the exhaust. But if efficiency drops below 92%, it will usually turn on the MIL lamp. Newer vehicles have to meet an even tougher Low Emission Vehicle (LEV) requirement, so there is even less room for leeway. A drop in converter efficiency of only 3% can cause emissions to exceed federal limits. The LEV standard allows only 0.225 grams per mile of hydrocarbons.

Some OEMs have updated calibrations for the catalyst monitors. The new calibration can then be re-flashed into the PCM. But, if the vehicle already has a damaged converter, the re-flash will do nothing at all for it. But, if the converter is near the threshold limit, the re-flash may extend the life of the converter and prevent the light from coming on for another 10,000 or even up to 80,000 miles.

Causes Of Converter Efficiency Loss

Faulty O2 sensors can also lead to converter inefficiency. One of the things a lot of techs neglect to check is probably the easiest thing to check ­— the O2 sensor connections. The connector not only is the supply for the voltage and grounds, but the source of the needed air supply to the zirconium sensor. If the connector is full of oil or debris, no air can internally pass down the wire leads to the sensor. The old one-wire O2 sensors had a perforated area on the outside and didn’t use the wire leads as the oxygen supply.

Years ago, I had a car that came in with silicone sealant completely engulfing the connectors. A code was present, but the damage was already done. All four O2s had to be replaced. The converter efficiency was in question, but after running the monitors several times the code never came back.

Obviously, tuneup-related items have to be factored into the efficiency of the converter. Anything from PCV valve condition, or broken exhaust hangers that damage the converter’s inner structure, to EGR valve and related EGR problems can all affect the efficiency. Exhaust leaks ahead of the O2 sensors can also greatly affect the efficiency.

Installing the wrong O2 sensors in the wrong position can also be a problem. Just for the record, B1 sensors are on the No. 1 cylinder side of the engine, while B2 sensors are on the opposite side. It wouldn’t be the first time I’ve seen the rear O2 in the front, or a vehicle with a B1 sensor code and somebody changed the B2 sensor. Keep in mind that a lot of vehicles now have multiple catalytic converters and more care has to be taken to ensure you’re changing the correct one.

As you can see, the efficiency of today’s cars is not based on only just one part but on the overall condition of all the components involved. Preventive maintenance can help lengthen the life of a catalytic converter, as well as paying attention to the service light when a code for converter efficiency pops up.

Keep in mind the efficiency of the converter is determined by what is going on in the combustion chamber and what the PCM is being told by the O2 sensors. For the most part, an efficiency code is the result of something that has already occurred and not necessarily a catalytic converter failure. So, take the proper steps to diagnose and repair the cause, not just analyze the results.

You May Also Like

AC Service – R1234yf

With a few simple steps, you can ensure that your A/C machine is properly maintained and ready for the upcoming A/C season!

Summer is just around the corner, and this is a perfect time to get your air conditioning machine serviced before the busy A/C season hits your garage bays. As the summer winds down and we move into the cooler months, most A/C machine usage winds down as well, with the machine sitting idle for longer periods of time, often unserviced at the end of the season. Now is the perfect time to get it ready to prevent any unwanted “downtime” from a machine that wasn’t serviced. Let’s look into what you can do to get your equipment ready.

Ignition Coil Output

To see inductance inside the primary windings, use an amp probe placed around the positive wire for the ignition coil.

Compressor Oil for R1234yf

Working on R-1234yf systems is not that different from the R-134a variety.

Turbochargers on Minis

No matter if it is a BMW or MINI, when the engine stops turning, the oil flowing to the turbocharger stops.

How Extended Interval Oil Filters Have Been Improved

Over time, the oil filter can collect enough contaminants to become restricted. Here’s why new filters are better.

Other Posts

How-to Complete Emissions Monitors Faster

This video will focus on how a product like CAT COMPLETE can improve the chances of completing the monitors faster. This video is sponsored by Rislone.

Forecast: 80% Drop In U.S. Transportation Emissions By 2050

NREL’s study highlights rapid adoption of zero-emission vehicles as crucial for an 80% emissions reduction.

Understanding Emissions

Modern EVAP systems are selective with how they vent vapors back into the engine. Sponsored by Standard.

SMP Expands Emission Control Program

SMP’s Emission Control program offers more than 1,500 EVAP components and 4,000 products for crankcase and EGR emissions.