BMW TPMS

BMW TPMS System Breakdown

Some BMW models require the use of the iDrive system to reset the TPMS system.

BMW has offered Tire Pressure Monitoring Systems (TPMS) on most of its vehicles since 2002. Some of those early vehicles from 2002 and 2003 models have an indirect system called Flat Tire Monitor (FTM) that compares the inputs of the wheel speed sensors to detect a flat tire. These early indirect and direct systems were implemented not to meet the 2007 government mandate, but to inform the driver when a run-flat tire was deflated.

The direct systems in use since those mandates use sensors mounted in the valve stems and have a lifespan of six to 10 years of battery life, depending on the drive cycles. Inside the wheel wells are the antenna and transponder for the sensor. There are two types of antenna/ transponders. The most common transponder is about six by one inch long; the other type resembles a large matchbox. The antenna/transponder units connect to a control unit that is mounted in the dash or trunk. This unit connects to the vehicle through the CAN BUS.

If you are to take one thing away from this article, it is this: The owner’s manual contains all of the TPMS reset procedures for that specific vehicle. When faced with servicing one of these systems, it is important not to panic. If the vehicle has a full-size spare tire like on some of the X-series SUVs, it is equipped with a sensor. 

Here are other quick reminders: On some of these models, the valve stem needs to be mounted in a certain direction in the well. On some models, the pressure can only be monitored when it is mounted. Temporary spares do not have a wheel sensor. If a temporary spare is mounted at any wheel position, the TPMS system will become “inactive” after several minutes.

Some early systems automatically adjust and recommend pressure settings based on changes in ambient air temperature. If the temperature is significantly cooler than the original initialization temperature for 14 days, the system will display an “Autumn Warning” light, to prompt the driver to recheck and inflate the tires because of cold weather. This feature was dropped on most systems after the 2009 model year.

Scan tools or TPMS-specific tools are not required to reset the system after rotation or sensor replacement. The resetting of sensors on all models can be performed through a button on the dash, turn signal stalk or the iDrive interface. But if the system has a malfunction code, a scan tool with the right software can help you pinpoint the problem.

Some BMW models require the use of the iDrive system to reset the TPMS system. The knob is like a computer mouse that is used to highlight menus and icons on the screen. Once an item is selected, just press down on the wheel.

2007-’10 BMW 1 Series Version With iDrive

1. Inflate tires to recommended pressures.

2. Call up the iMenu on the iDrive screen.

3. Select Settings menu.

4. Select Car/Tires and press controller. If necessary, switch to the top field. Turn the controller until “Tires: RDC” is selected and press the controller.

5. Start the engine.

6. Select Confirm tire pressure and press the controller.

7. Drive off. Initialization is completed during at least 15 minutes of driving.

2007-’10 BMW 1 Series Version Without iDrive

1. Inflate all tires to correct pressure specifications.

2. Start engine, but do not drive off.

3. Touch the scroll lever on the turn signal stock up or down until the TPMS symbol and the word RESET appear.

4. Press the button on the end of the stalk to confirm selection of Run Flat Indicator.

5. Press and hold for five seconds until a check/tick appears after RESET.

6. Test drive the vehicle to complete the reset.

2006-’08 3-Series (E46)
2009-’11 3-Series (E92/E93) Without iDrive

1. Inflate all tires to correct pressure specifications.

2. Start the engine, but do not drive off.

3. Push scroll switch on the turn signal stalk up or down, until the TPMS symbol and the word RESET or “INIT” appear in the display.

4. Push button on the end of the stalk to select RESET or “INIT.”

5. Push and hold button 1 (for about 5 seconds) until “resetting” appears, telling you the reset protocols has started.

6. Drive the vehicle for 15 minutes to complete reset. If driving is interrupted, reset will resume at the next drive cycle. There is no need to go through the menu again.

2009-’13 3-Series 

(E92/E93) With iDrive

1. Inflate all tires to correct pressure specifications.

2. Press the menu button below the iDrive wheel.

3. Use the wheel and select the tab “Vehicle Info” and press the controller.

4. Select “Vehicle Status” and press the controller.

5. Select “RESET TPM” and press the controller.

6. Drive the vehicle for a few minutes to complete reset.

Note: Do not reset the system when compact spare tire or snow chains are installed.

2004-’05 3-Series (E46)

2004-’06 X5 (E53)

2003-’08 Z4 Roadster (E85)

2004-’10 X3 (E83)

1. Inflate all tires to correct pressure.

2. Start the engine.

3. Press and hold the TPMS RESET button until the TPMS LED light changes to yellow for a few seconds.

4. Drive the vehicle through various speed ranges for about 15 minutes. If driving is interrupted, reset will resume at the next drive cycle.

2007-’10 5-Series Sedan (E60)

2007-’10 6-Series (E63/E64)

2007-’09 X5 (E70)

1. Inflate all tires to correct pressure specification as indicated on the Vehicle Tire Placard.

2. Press MENU button on the iDrive.

3. Press the controller to open the iDrive menu.

4. Select “Vehicle Info” and press the controller.

5. Select “Vehicle Status” and press the controller.

6. Turn controller to select “Reset TPM” and press the controller.

7. Start the engine.

8. Select “Reset” and press.

9. Select “Yes.”

10. Begin driving the vehicle. The display for the iDrive will say “Status: Resetting TPM.” When the drive cycle is complete the screen will say “Status: TPM Active” indicating when reset is complete.

2004-’06 5-Series (E60)

2004-’06 6-Series (E63/E64)

1. Inflate all tires to correct pressure specification.

2. Press the MENU button.

3. Press the controller to open the iDrive menu.

4. Select Vehicle Settings tab.

5. Select FTM tab.

6. Start the engine.

7. Select “Set Tire Pressure.”

8. Select “Yes.”

9. Start driving the vehicle. The screen will say “Initializing” until the drive cycle is complete. When complete, the screen will say “TPM Active,” indicating system reset. If driving is interrupted, reset will resume at next drive cycle.

2004-’06 7-Series (E65)

1. Inflate all tires to correct pressure specification as indicated on the Vehicle Tire Placard.

2. Start the engine.

3. Press the MENU button.

4. Move controller toward SETTINGS and release.

5. Turn controller to select VEHICLE and press the controller.

6. Select “FTM” and press the controller.

7. Select “SET” and press the controller.

8. Begin driving the vehicle. “Status: FTM IS BEING INITIALIZED” will appear in the display. If driving is interrupted, reset will resume at next drive cycle. When reset is complete, “Status: ACTIVE” will appear in the display.

2007-’08 7-Series (E65)

1. Inflate tires to correct specs.

2. Press MENU button.

3. Use the iDrive controller to select “Settings.”

4. Turn controller to select “Vehicle” and press the controller.

5. Select “TPM” and press the controller.

6. Start the engine.

7. Select “Reset” and press the controller.

8. Select “Yes” and press the controller.

9. Begin driving the vehicle. “Status: Resetting TPM” will appear in the display. If driving is interrupted, reset will resume at the next drive cycle. “Status: TPM ACTIVE” will appear in the display when reset is complete.

You May Also Like

Volvo Modular Engine Service

The Volvo Modular Series engine outlasted Ford and was retired by Geely. The Volvo modular design that can have four, five or six cylinders made its debut in 1990 in the 960 sedan as a six-cylinder and never stopped improving. VOLVO SPA AND CMT What is a Volvo? In 1999 the company was acquired by

The Volvo Modular Series engine outlasted Ford and was retired by Geely. The Volvo modular design that can have four, five or six cylinders made its debut in 1990 in the 960 sedan as a six-cylinder and never stopped improving.

VOLVO SPA AND CMT

What is a Volvo? In 1999 the company was acquired by Ford. By 2006 all of the boxy Volvo platforms were gone and replaced by Ford platforms. But, the engines remained uniquely Volvo. In 2010, Volvo was purchased by the Chinese automaker Geely, and the purge started again.

Audi Active Suspension Service

The key to servicing these systems is proper information and understanding precisely how these systems operate.

How To Service BMW Tire Monitor Systems

BMW has offered Tire Pressure Monitoring Systems (TPMS) for more than 20 years. These early indirect and direct systems were implemented not to meet the 2007 government mandate but to inform the driver when an expensive Michelin or Bridgestone run-flat tire was deflating. Some 2002 and 2003 models have an indirect system called Flat Tire

VW DSG Maintenance

A DSG transmission is lighter than a comparable automatic with the same number of speeds.

Tech Tip: Checking Transmission Fluid Levels When Cold or Hot

Checking the fluid level before the transmission has reached the specified temperature might cause a false reading

Other Posts

Servicing Mercedes-Benz AMG Brakes

Take a look at some of the things you need to know in order to service the brakes on a Mercedes-Benz AMG vehicle.

Air Ride Diagnostics: Reservoirs and Compressors

The secret to diagnosing air ride problems is knowing what criteria the system uses to regulate the compressor/reservoir and having the right tool.

TPMS Tools and Sensors

Transform TPMS with advanced diagnostics and sensor programming. This video is sponsored by Bosch.

Mercedes EQS Service Opportunities

EQ is the EV brand for Mercedes. It is the equivalent of Audi’s Etron.