BMW High Pressure Fuel Pump, Tank and System Repair

BMW Fuel System Repair Essentials

The BMW N54 fuel pump recall a few years ago brought to light the importance of the integrity of the fuel system and how it can contribute to the overall reliability of a vehicle. These fuel quality issues apply to all BMW vehicles with either port or direct injection. The underlying message here is that if the cleanliness and overall integrity of the fuel tank is ignored, it will damage any fuel pump. This is why addressing the fuel tank is essential during any pump replacement to prevent costly comebacks that can also hurt your reputation.

The BMW N54 fuel pump recall a few years ago brought to light the importance of the integrity of the fuel system and how it can contribute to the overall reliability of a vehicle. While BMW never officially stated what was causing the high-pressure fuel pumps to fail, some put the blame on low-quality fuel that might have been contaminated or had higher-than-normal ­levels of ethanol.
These fuel quality ­issues apply to all BMW ­vehicles with either port or direct injection. The underlying message here is that if the cleanliness and overall integrity of the fuel tank is ignored, it will damage any fuel pump. This is why addressing the fuel tank is essential during any pump replacement to prevent costly comebacks that can also hurt your reputation.

If a vehicle gets 20 miles to the gallon, then more than 5,000 gallons of gas (from many stations) will go through the tank in 100,000 miles. And, during this time, sediment, rust and debris from the pump can find its way into the tank.
Removing all contaminants is critical. If possible, have the tank steam-cleaned at a radiator shop that performs these services. They can ­recondition a tank and check for leaks that you may not be able to spot. Your goal in cleaning the tank is to restore the environment inside the tank to its original state, before it moved off the assembly line.
If you think the new sock or strainer on the fuel pump will catch all of the bad stuff, you’re wrong. The typical sock or strainer is designed to catch contaminants that are ­between 50-100 ­microns in diameter. For comparison’s sake, the size of a human hair is 40 microns. A typical ­inline fuel filter can catch particles as small as 10 microns. The sock also has a limited capacity due to its small surface area.
Always install a new filter. Sounds simple, but it’s often ­forgotten. The old filter can restrict flow and cause the new pump to work harder. This makes for a hotter-­running pump that fails sooner.

Bad grounds and connections can also kill a new pump. Check the connector for any signs of thermal damage that may indicate there was a voltage drop or a circuit with high resistance. Do not ­assume the old pump caused the thermal damage. Bad grounds and circuits will stay with the vehicle and damage the new pump.
Filter the fuel before you put it back in the tank. If a fuel pump went through a full meltdown, chances are pieces from the old pump are still in the removed fuel. Many fuel caddies have built-in filters.
Check the EVAP system before returning the car to the customer. It takes at least one drive cycle for most vehicles to set an EVAP code. A leak due to disturbing the lines may not set a code during the initial test drive. The code may come on after the vehicle has been sitting for awhile or after a certain temperature has been reached.
Check the system with a scan tool and/or smoke machine ­before delivering the car to the customer. Some scan tools and vehicles can perform a self-leak check. Fuel filler necks are especially susceptible to leaks if the tank has been dropped.
In the Rust Belt states, corrosion on the top of the tanks and on the fuel lines can ­become a big headache during fuel pump ­replacement. This comes from brines that are used on roads to prevent icing. Brines stick to ­vehicles — even the tops of fuel tanks — long after the snow storms have passed and even into summer. Then, every time it rains, the brines are reactivated and start to corrode the tank.
Be sure to check the straps and the tank mounting hardware. In 2010, one automaker recalled 1.2 million trucks due to corrosion of the straps that held up the gas tank.
Note: It’s a good practice to ­inspect the fuel lines for corrosion before starting the job. ­Nothing is worse than having to call the ­customer ­because a line collapsed due to corrosion ­during removal or installation.

Fuel Tank Cleaning Procedures
1. Once the tank has been removed, drain all fuel from the tank. Use only an approved container or a fuel caddy to filter and store the fuel.
2. Clean accumulated road debris or rust from the top of the fuel tank, especially around the module or hanger assembly to avoid contaminating the fuel tank.
3. Remove the lock ring.
4. Remove the module or hanger assembly.
5. Clean and flush the tank with water before installing the new module or hanger assembly.
6. Swirl the fuel tank around in a circular motion to collect any debris remaining in the fuel tank.
7. Slowly and carefully poor the fuel out of the tank into the approved container or fuel caddy.
8. Turn the fuel tank over, then tap the bottom to remove any debris.
9. If a tank can be cleaned, it’s important to use high-pressure soap and water to remove the dirt. Late-model fuel tanks are difficult to clean because of their internal baffling. The tank should then be thoroughly dried by circulating air through the tank or by simply placing it in the summer sun. In many cases, a fuel tank replacement is the most cost-effective and safest alternative.
10. If possible, take a lint-free shop towel and wipe the inside of the fuel tank until it is clean.
11. Dry out the fuel tank completely with compressed air.
12. Inspect the fuel tank carefully. If the tank is rusted inside or shows signs of physical damage, it must be repaired or replaced.
13. After the tank has been dried with compressed air, let it sit for 30 minutes.
Courtesy of the Fuel Pump Manufacturers Council.
BMW Fuel Pump Tech Tips 
Here are some recent technical service bulletins related to BMW fuel pumps.
#1. N20 Engine: Ticking Noise From High-Pressure Fuel Pump
Situation: The customer complains of a high-frequency ticking noise from the engine compartment. The noise can be heard inside and outside the vehicle.
Cause: Mechanical vibrations inside the high-pressure fuel pump.
Correction: Install a high-pressure fuel pump cover (P/N 13 51 7 629 129). The plastic acoustic cover will snap onto the high-pressure fuel pump.
Do not remove the fuel lines or the high-pressure fuel pump to install the acoustic cover.

figure 1

#2. N14, N18 Engine: High-Pressure Pump Repair ­Instructions
The current version of the repair instruction “Removing and installing or replacing high-pressure pump” has a procedure error. This current version of the repair instruction states to replace the high-pressure supply hose on the N14 engine and to not replace the high-pressure supply hose on the N18 engine. The N18 portion of the repair instruction is incorrect.

Figure 2

As an interim solution, follow the procedure outlined below:
Continental High-Pressure Pump: All vehicles equipped with the N14 engine (all production); all N18 vehicles produced up to March 2012 are equipped with a Continental High-Pressure Pump (see 1 in Fig. 1).
When the N18 engine is fitted with a Continental High-Pressure Pump, the high-pressure ­supply hose (see 2 in Fig. 1) must be replaced when making repairs.
Bosch High-Pressure Pump: All vehicles equipped with the N18 engine and produced from March 2012 and later.
When the engine is fitted with a Bosch High-Pressure Pump (see 1 in Fig. 2), the high-pressure supply hose (see 2 in Fig. 2) must not be replaced when making repairs.

You May Also Like

ASE Education Foundation, Goodguys Continue Partnership

Goodguys is one of many industry relationships the foundation has developed to help solve the technician shortage.

The ASE Education Foundation and Goodguys Rod and Custom Association (Goodguys) are continuing their partnership and will conduct educational awareness seminars at select Goodguys events throughout the 2024 season.

Since its inception, the ASE Education Foundation has brought industry and education together to develop entry-level technicians. Goodguys is one of many industry relationships the Foundation has developed to help solve the technician shortage.

BMW Diagnostics: Low Airflow After Cabin Filter Replacement

Models:  F97 X3 M  F98 X4 M G01 X3 G02 X4 G20 3-Series SITUATION After replacing the microfilter during a previous service, the customer notices that the ventilation system airflow rate is noticeably less. This leads to perceived lower cooling power. The customer may also notice that external odors enter the vehicle. Related Articles –

Volvo Modular Engine Service

The Volvo Modular Series engine outlasted Ford and was retired by Geely. The Volvo modular design that can have four, five or six cylinders made its debut in 1990 in the 960 sedan as a six-cylinder and never stopped improving. Related Articles – How To Service BMW Tire Monitor Systems – VW DSG Maintenance –

BMW Cooling System Problems

Let’s take a closer look at this unique water pump, how to replace it efficiently and what other components should be replaced along with it.

Audi Active Suspension Service

The key to servicing these systems is proper information and understanding precisely how these systems operate.

Other Posts

Valvoline Celebrates Female Service Center Employees

As women make up more than half of all drivers in the United States, Valvoline is taking steps to increase their vehicle care confidence.

BorgWarner Announces Plan to Reduce Supply Chain Emissions

A partnership with Manufacture 2030 will support BorgWarner in reaching its Scope 3 emissions reduction goal.

Snap-on Continues to Offer Free Weekly Product Training Sessions

The online training and question and answer sessions are free of charge.

AMSOIL Introduces New OE 0W-40 100% Synthetic Motor Oil

The new OE 0W-40 is primarily for newer RAM HD trucks equipped with the 6.4-liter Hemi engine.