Alternator Testing Diagnostics

Alternator Testing Diagnostics Are Getting More Complicated

One test is not enough if you are diagnosing a charging system problem. All too often, if only battery voltage is present with the engine running the alternator is condemned as the source of the problem. If this is the case, it means that the alternator is not charging, but does not reveal why.

One test is not enough if you are diagnosing a charging system problem. All too often, if only battery voltage is present with the engine running the alternator is condemned as the source of the problem. If this is the case, it means that the alternator is not charging, but does not reveal why.

For some alternators, it’s normal to see as low as 13 volts, while a constant 13.6 volts can be an indication of a problem. For others, it’s normal to see as high as 16 volts for long stretches. Still, it’s perfectly normal for others to see the alternator intermittently not charge at all.

This wide discrepancy in voltages is due to the fact that the ECM or PCM controls most alternators in an effort to improve fuel economy. This means that load on the engine is controlled to reduce parasitic loss at the crankshaft. Alternator output is “on demand” when there are loads detected or the battery needs to be charged.

Charging voltage varies depending on ambient temperature. The actual charging voltage designed into a voltage regulator is dependent upon factors such as how far the alternator is located from the battery and the ambient air temperature surrounding the battery as calculated by the PCM. This is why the ambient and underhood temperature data is critical for the charging system.

Another factor determining battery voltage is an automatic transmission with five or six speeds that can drastically reduce engine speed when cruising. Many modern engines operate well under 2,000 rpm until they reach highway speeds of about 60 to 70 mph. Consequently, if the alternator doesn’t maintain rated charging voltage at lower engine speeds, the battery will discharge under heavy accessory loads. In most cases of undercharging, the alternator may have an incorrect diameter pulley installed, the drive belt may be slipping or the alternator itself might be under capacity for the vehicle application.

Although load-testing an alternator provides a quick way to test for drive belt slippage, keep in mind that an alternator can easily be overheated when testing for maximum output during low-speed operation for an extended period. Most alternators will not be able to keep up with the load when idling, and the lack of cooling compounds the problem even further. Some systems might even stop charging if an extreme load is detected and will set a code.

Take time to look at the service information so that you don’t overlook critical problems and to prevent a misdiagnosis.

The other critical tool to effectively diagnose an alternator is a scan tool. On older vehicles, the battery light would turn on the alternator light when the alternator output or battery voltage dropped below a preset value. The battery light on modern vehicles, however, is controlled by data and trouble codes. This is why a scan tool is essential in diagnosing a charging system, as these codes can lead to a faster and more accurate diagnosis. Codes for the alternator can be found in the engine control module and the modules that control the distribution of power to the vehicle. In addition, most modules on a vehicle will set a code if low system voltage is detected.

Testing the Battery

The rule of thumb that states 12.6 volts equals a fully charged battery and 12.2 volts means it is 25 percent charged, is starting to change with some modern batteries and charging systems.

If there is a bad cell, for example it’s dead or weak, normal charging voltage can’t be achieved. The alternator will overcharge the remaining cells and boil the electrolyte in the other cells. At the other extreme, a battery that is sulfated due to being undercharged or not seeing constant use will maintain normal charging voltages. The symptoms of a sulfated battery are that it charges very quickly and produces a very low amperage discharge rate.

Fewer and fewer batteries allow the technician to view electrolyte levels or test individual cells. This is why testing with an electronic conductance tester that measures cold cranking amps is the most accurate way to assess the condition of the battery.

Because new batteries typically test as much as 25 percent higher than their rated capacities, a recently replaced battery with a bad cell can occasionally pass both a conductance and a load test.

Parasitic Draws

As a rule, the key-off current drain on most late-model vehicles should be less than 50 milliamps (mA). If a draw is depleting a battery, it can mean extra stress on the alternator and charging system. But, on some vehicles, it might be normal to have even greater draws for up to 10 minutes after the keys have been removed from the ignition.

During this period, the serial data buses could be communicating and performing some digital housekeeping. Also, systems like air ride, evaporative emissions and auxiliary water pumps could still be active long after the vehicle has been parked. This is why in some service information for modern vehicles, an OBDII breakout box and a scan tool are needed to solve some intermittent parasitic power drains.

Check The Pulley

Many late-model vehicles use a decoupler pulley on the alternator. These new pulleys allow the alternator to “free-wheel” or “overrun” when the belt suddenly slows down. This prevents the belt from slipping and reduces vibration. Best of all, in this scenario, the system needs less tension and a narrower belt can be used. This can result in a 1.5-2% fuel economy improvement. However, these pulleys have a limited lifespan due to how they operate internally.

Some replacement alternators come without a pulley or a solid pulley. If the replacement alternator does not come with a new pulley, be sure to install the correct pulley with it. If not, the replacement alternator can fail sooner than expected.

If you don’t see the recommended voltage when you check charging voltage at the battery with the engine idling, check the wiring connections at the alternator — not just visually or by wiggling the wires or connectors, but checking for excessive resistance by doing a voltage drop test. Many so-called alternator problems turn out to be nothing more than a bad connection at the alternator or a bad wiring harness.

If You See This

If you see a modern vehicle that measures the life or temperature of the battery, it is a bad practice to use the positive and negative battery terminals to power aftermarket accessories. The extra connections can cause the battery to incorrectly report the state of discharge, despite a normal battery condition. This can cause overcharging and/or codes to be set that may cause the charging light on the instrument cluster to illuminate.

You May Also Like

Mercedes-Benz AC Service

Here’s what you need to know about R-1234yf refrigerant in Mercedes-Benz vehicles.

As the summer approaches, we all know what will be coming: air conditioning repairs. Just like you’ll sell more wipers on a rainy day, you’ll never see more air conditioning complaints than on a hot, sunny day. As a former Mercedes-Benz technician, I can tell you that A/C complaints were very common at the dealership. So, what do you need to know about R-1234yf refrigerant in Mercedes-Benz vehicles?

Battery Charging and Diagnostics

Here are six tips to use when diagnosing a vehicle with a dead battery. 

Euro HID Diagnostics

Here are five diagnostic tips to resolve issues with these systems.

Transmissions – CVT

Knowing what the common issues are & understanding the options available to isolate & fix problems are the keys to success.

Engineering Better Belt Systems

The belt drive system is working hardest when the engine is at idle.

Other Posts

Timing The BMW N53 And N54

The BMW N53 (naturally aspirated) and N54 (turbocharged) engines were among the first BMW engines to come with variable valve timing on the intake and exhaust camshafts. The N53 and N54 straight-six has unfairly earned a bad reputation for reliability with technicians due to timing chain and variable valve timing problems. The reputation comes from

Spark Plug Fouling

Understanding why spark plugs get dirty.

Key Programming

Three situations might require key programming capabilities at your shop.

Solving Intermittent Overheating

New cooling systems anticipate and influence changes in coolant temperature.