Alignment Specs: BMW 3-Series 1998-2006 E46

Alignment Specs: BMW 3-Series 1998-2006 E46

The BMW E46 was the best selling generation of the 3-Series. The rear-wheel drive sports sedan is one of the more complicated cars to align, but it has many service and repair opportunities.

The BMW E46 was the best selling generation of the 3-Series. The rear-wheel drive sports sedan is one of the more complicated cars to align, but it has many service and repair opportunities.
The front suspension is a strut design with the familier sickle-shaped control arm that was introduced on this platform in 1983. The rear suspension carried over from the E36, but it has a unique rear trailing arm design.
The best advice given by many BMW dealership technicians is to measure the ride height before starting an alignment.

The rear suspension is sensitive to changes in both front and rear heights. BMW specifies the ride height must be within ±2mm. The measurement is taken between lip of the wheel well and the bottom of the rim. The specifications vary between coupes, sedans and suspensions packages.
Check your service information for the right spec. 
Front Suspension
The number one component to fail on the BMW E46 front suspension is the rear control arm bushing. The bushing is attached to the uni-body directly next to the driver and passenger foot wells. When this bushing gets soft, it will change the toe, camber and caster. This will result in inside edge tire wear. 
Camber can be adjusted ±0.5º  by moving the upper strut mount in slots cut in the strut tower. If you cannot get the camber into spec with this adjustment, start looking at the ride height, bushings and cradle. Other more radical camber adjustment kits are available that can change the camber by -3.5º, but these are for track day cars. 
Adjusting the toe is the same as any other vehicle. BMW makes it easier with marks on the steering rack and shaft. If the toe is adjusted properly and the marks match up, you should not have to recalibrate the steering angle sensor.

But, the output for the steering angle sensor should be checked with a scan tool to make sure it reads that it is centered. If a tie rod or the rack is replaced, the sensor must be recalibrated. Also, the steering angle sensor must be coded or reflashed if it has been replaced.
Rear Suspension
The rear suspension on a BMW E46 is very unique.  The design is called a "C" arm type. BMW calls it an “Elastokinematics” suspension system that is designed to be pliable (like elastic) which absorbs the longitudinal and axial forces of driving providing better handling characteristics. The rear has more than a dozen mounts and bushings that can soften and eventually fail. This can result in noise and change in the alignment angle.

The design may seem complex, but the engineers at BMW designed the trailing arm and links to change camber and toe as the vehicle rolls and squats. This is why measuring the ride height before the alignment is critical.  
The differential is mounted to the sub frame using a hydraulic mount. The sub frame is mounted to the body at four vibration absorbing rubber mounts. The upper transverse control arms are made from cast aluminum for weight saving.
Some drivers may complain of a pulling during acceleration and braking. This could be due to worn bushings. 
A change in camber also means a change in toe; this means that camber must be adjusted first. Camber is adjusted using an eccentric bolt on the lower control arm. If the collar nut is tightened more than 10 times during adjustment, it must be replaced again because the self-locking effect becomes too slight.
Toe is adjusted by changing the position the plates that connect the trailing arm to the body called a bearing pedestal. Release screws 1-1/2 turns at bearing pedestal and attach special tool 32 3 030 to screw head and to a notch in the plate. Turn special tool and adjust toe-in to specified value.
Under certain circumstances, a fracture in the steel body structure could form in the area around one of the rear axle carrier mounting points. As a result, a distinct clicking noise can be heard from the area of the rear axle carrier during certain driving conditions. Specifically, the noise may be heard during load reversals on the rear axle, such as when starting from a stop, engaging forward or reverse gears, or when rapidly changing gears.
As a result of the proposed settlement of a class action lawsuit, a national sub-frame inspection and repair program has been developed. Under this program, any current owner of a U.S.-specification E46 3 Series car may have his or her E46 inspected to determine whether any damage to the rear axle carrier support is present. If damage to the rear axle carrier support is found during the inspection, and the vehicle qualifies for the repairs, BMW will repair the vehicle using one of two approved repair procedures; either a structural epoxy repair or replacement of the rear axle carrier, depending on the evaluation of the damage. 

You May Also Like

AUDI Outside Air Temperature Readings

Incorrect readings can be avoided.

With the recent changing of seasons, it is possible to see a 20- to 30-degree temperature change from when the car is parked in the evening and driven again in the morning. Some customers may say they think the ambient temperature is not reading accurately. To achieve a "smoothing" effect of the displayed outside ambient temperature, the value shown does not instantaneously follow the temperature sensor measurement.

Mercedes-Benz ABC Suspensions

The system provides great ride & handling, but it can be complicated to service if you do not have the right training.

Audi TFSI/FSI: Oil Consumption And Carbon Buildup

Technical Service Bulletins can be valuable in helping solve vehicle problems. But sometimes, it takes multiple TSBs to find a pattern failure or the “root cause” of a problem. In the case of the Audi/VW 2.0L Fuel Stratified Injection (FSI) engine introduced in 2006, three problems related to engine carbon and fuel issues are connected

BMW Diagnostics: Low Airflow After Cabin Filter Replacement

Models:  F97 X3 M  F98 X4 M G01 X3 G02 X4 G20 3-Series SITUATION After replacing the microfilter during a previous service, the customer notices that the ventilation system airflow rate is noticeably less. This leads to perceived lower cooling power. The customer may also notice that external odors enter the vehicle. Related Articles –

Carbon Deposit Q&A

Follow along to learn more about carbon deposits.

Other Posts

Philips Announces GoPure GP5212 Automotive Air Purifier

It uses a 3-layer filter to deliver cleaner, healthier, fresher air on the go, Lumileds said.

AACF Launches 65th Anniversary Fundraising Initiative

The campaign aims to raise $65,000 through 1,000 donations of $65 each.

Standard Motor Products Announces 123 New Numbers

The release provides new coverage in 53 distinct product categories and 47 part numbers for 2023 and 2024 model-year vehicles.

BendPak Founder Don Henthorn Passes Away

Grew company from small machine shop to global leader in car lifts and garage equipment.